manualshive.com logo in svg

Maxim Dallas Semiconductor DS3171, General Description Manual, Page: 165 / 234

Share
Download
Maxim Dallas Semiconductor DS3171 General Description Manual Download Page 165

DS3171/DS3172/DS3173/DS3174 

 

 

165 

12.7 FEAC Controller 

12.7.1  FEAC Transmit Side Register Map 

The transmit side utilizes five registers.  

Table 12-19. FEAC Transmit Side Register Map 

 

Address 

 

Register 

 
Register Description 

(0,2,4,6)C0h FEAC.TCR 

FEAC Transmit Control Register

 

(0,2,4,6)C2h FEAC.TFDR 

FEAC Transmit Data Register

 

(0,2,4,6)C4h FEAC.TSR 

FEAC Transmit Status Register

 

(0,2,4,6)C6h FEAC.TSRL 

FEAC Transmit Status Register Latched

 

(0,2,4,6)C8h FEAC.TSRIE 

FEAC Transmit Status Register Interrupt Enable

 

(0,2,4,6)CAh -- Unused 

(0,2,4,6)CCh -- Unused 

(0,2,4,6)CEh -- Unused 

 

12.7.1.1   Register Bit Descriptions 

 
Register Name: 

FEAC.TCR 

Register Description: 

FEAC Transmit Control Register 

Register Address: 

(0,2,4,6)C0h 

 
Bit 

#  15 14 13 12 11 10  9  8 

Name 

-- -- -- -- -- -- -- -- 

Default 

0 0 0 0 1 0 0 0 

 
Bit 

# 7 6 5 4 3 2 1 0 

Name 

-- -- -- -- -- 

TFCL 

TFS1 

TFS0 

Default 

0 0 0 0 0 0 0 0 

 

Bit 2: Transmit FEAC Codeword Load (TFCL)

 – A 0 to 1 transition on this bit loads the transmit FEAC processor 

mode select bits (TFS[1:0]), and transmit FEAC codes (TFCA[5:0] and TFCB[5:0]). Note: Whenever a FEAC 
codeword is loaded, any current FEAC codeword transmission in progress will be immediately halted, and the new 
FEAC codeword transmission will be started based on the new values for TFS[1:0], TFCA[5:0], and TFCB[5:0].. 

Bits 1 to 0: Transmit FEAC Codeword Select (TFS[1:0])

 – These two bits control the transmit FEAC processor 

mode. The TFCL bit loads the mode set by this bit.  
 

00 = Idle (all ones) 

 

01 = single code (send code TFCA ten times and send all ones)  
10 = dual code (send code TFCA ten times, send code TFCB ten times, and send all ones) 

 

11 = continuous code (send code TFCA continuously) 

 

 

Summary of Contents for Dallas Semiconductor DS3171











































































































































































































































Reviews:

No comments