manualshive.com logo in svg

Maxim Integrated MAX20335, Manual, Page: 46 / 67

Share
Download
Maxim Integrated MAX20335 Manual Download Page 46

Table 9. IntA Register (0x05)

Table 10. IntB Register (0x06)

ADDRESS:

0x05

MODE:

Clear On Read

BIT

7

6

5

4

3

2

1

0

NAME

Therm 

StatInt

ChgStatInt

ILimInt

UsbOVPInt

UsbOk

Chg 

ThrmSdInt

Therm 

RegInt

Chg 

TmoInt

ThermStatInt

Change in ThermStat caused interrupt.

ChgStatInt

Change in ChgStat caused interrupt, or first detection complete after POR.

ILimInt

Input current limit triggered caused interrupt.

UsbOVPInt

Change in UsbOVP caused interrupt.

UsbOk

Change in UsbOk caused interrupt.

ChgThrmSdInt

Change in ChgThrmSd caused interrupt.

ThermRegInt

Change in ChgThrmReg caused interrupt.

ChgTmoInt

Change in ChgTmo caused interrupt.

ADDRESS:

0x06

MODE:

Clear On Read

BIT

7

6

5

4

3

2

1

0

NAME

—

SysBLimInt

VLimInt

Thrm 

Buck1Int

Thrm 

Buck2Int

Thrm 

LDO1Int

Thrm 

LDO2Int

Thrm 

LDO3Int

SysBLimInt

Minimum SYS-BAT voltage limit caused interrupt

VLimInt

Input Voltage Limit caused interrupt

ThrmBuck1Int

Change in ThrmBuck1 caused interrupt.

ThrmBuck2Int

Change in ThrmBuck2 caused interrupt.

ThrmLDO1Int

Change in ThrmLDO1 caused interrupt.

ThrmLDO2Int

Change in ThrmLDO2 caused interrupt.

ThrmLDO3Int

Change in ThrmLDO3 caused interrupt.

MAX20335

PMIC with Ultra-Low I

Q

 Voltage Regulators and 

Battery Chargers for Small Lithium Ion Systems

www.maximintegrated.com

Maxim Integrated  

│

 

46

Summary of Contents for MAX20335




































































Reviews:

No comments