28
Maxim Integrated
Evaluates: DS34S132
DS34S132 Evaluation Kit
Table 4-2. General Configuration Parameter Descriptions
Note:
Source IP 1 and Source IP 2 can reside in different subnets. However, the IP mask is used for both source IPs. Either
Source IP 1 or Source IP 2 can be selected in the
Bundle Configuration
menu (see section
PARAMETER
DESCRIPTION
POSSIBLE VALUES
Source Mac Address 1
Port local MAC address
Up to 12 alphanumeric characters
Default: 08002E289D53
Source Mac Address 2
Second host MAC address.
Up to 12 alphanumeric characters
Default: 08002E2896C0D
Source IP 1
Host IP address (see note).
0.0.0.0
to
255.255.255.255
Default: 10.10.10.5
Source IP 2
Second host IP address (see note).
0.0.0.0
to
255.255.255.255
Default: 10.10.10.5
Default Gateway
IP address of default gateway.
0.0.0.0
to
255.255.255.255
Default: 0.0.0.0
Not Eth Type
Specifies what to do with packets received from
UPLINK port, where Ethertype does not match one of
the following: IP, MPLS, ARP, MEF, MEF OAM, or CPU.
Discard:
Drops these packets
CPU:
Passes these packets to the CPU
Default: CPU
ARP Wrong IP
Specifies what to do with ARP packets received from
UPLINK port, where IP is different from source IP.
Discard:
Drops these packets
CPU:
Passes these packets to the CPU
Default: CPU
Wrong IP
Specifies what to do with packets received from
UPLINK port with IP different from all source IPs.
Discard:
Drops these packets
CPU:
Passes these packets to the CPU
Default: CPU
ARP My IP
Specifies what to do with ARP packets received from
UPLINK port, where IP is identical to source IP.
Discard:
Drops these packets
CPU:
Passes these packets to the CPU
Default: CPU
Not TDMoIP Type
Specifies what to do with packets received from
UPLINK port, where UDP destination/source port is not
TDMoIP.
Discard:
Drops these packets
CPU:
Passes these packets to the CPU
Default: CPU
Not UDP Type
Specifies what to do with packets received from
UPLINK port, where protocol is not UDP.
Discard:
Drops these packets
CPU:
Passes these packets to the CPU
Default: CPU
OAM Packet
Specifies what to do with TDMoIP OAM packets.
Discard:
Drops these packets
CPU:
Passes these packets to the CPU
Default: CPU
Bundle Not Exist
Specifies what to do with packets received from
UPLINK port, where bundle identifier is not one of the
identifiers assigned in the TDMoP IC.
Discard:
Drops these packets
CPU:
Passes these packets to the CPU
Default: Discard
Max HDLC Frame Size
[1 - 1800]
Maximum size of HDLC packet in bytes (header and
FCS are not included).
1–1800
for IP
1–1800
for MPLS
Default: 1468
Ethernet Rate & Duplex
If autonegotiation is enabled, rate and duplex must be
configured to a value equal or greater than the rate
and duplex mode of the network. If autonegotiation
is disabled, the rate and duplex must be configured
equal to the rate and duplex of the network.
1: 100 FDX ANEG
2: 1000 FDX ANEG
3: 100 FDX
4: 1000 FDX
Default: 100M_FDX, ANEG
OAM Configuration
Selecting this options causes the
OAM Configuration
submenu to be displayed.
—