Matrix SPARSH VP710 User Manual Download Page 36

Page: 36 / 1046

Matrix SPARSH VP710 User Guide

•

Select

Standard SIP

, to operate the IP Phone in the standard mode. As soon as you select this mode, the

booting process initiates again and the start up screen displays “Welcome Initializing…please wait”. After

initialisation of the phone, the touch screen displays the following:

•

Time and date

•

Android Keys

•

Select

Extended SIP

, to operate the IP Phone in the extended mode. To know more, refer to the

EXTENDED SPARSH VP710 User Guide.

Tap

Settings->Status

to check the IP phone status, the touch screen displays the valid IP address, MAC

address, firmware version, etc.

If the IP phone has successfully passed through these steps, it starts up properly and is ready for use.

Phone Mode

Matrix SPARSH VP710 supports two phone modes,

Standard SIP

and

Extended SIP

. You can use the IP Phone

in either of the two modes as per your requirement. This section explains how to switch the phone mode from

Standard SIP

Extended SIP

or vice versa.

To change the Phone Mode

•

Swipe down from the top of the touch screen of the IP Phone.

•

Tap

Setting

•

Advanced,

enter the default password,

admin

•

Tap

Phone Mode

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands