Matrix SPARSH VP710 User Manual Download Page 352

Page: 352 / 1046

344

Matrix SPARSH VP710 User Guide

Redialing Numbers

To redial the last dialed number from your phone:

•

Press

twice.

A call to your last dialed number is attempted.

To redial a previously dialed number from your phone:

•

Press

when the phone is idle.

•

Tap the desired entry from the placed calls list.

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Matrix SPARSH VP710, User Manual, Page: 352 / 1046

Search results

Summary of Contents for SPARSH VP710

Reviews: