manualshive.com logo in svg

Matrix SPARSH VP710, User Manual

The Matrix SPARSH VP710 User Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidelines to help you make the most of your VP710. Get the manual now from manualshive.com and unlock the full potential of this exceptional product.

Share
Download
background image

336

Matrix SPARSH VP710 User Guide

Audio/Video Selection

1

Placing Calls using Audio Call/Video Call Option

To place a video/audio call:

Do one of the following:

•

Enter the desired number using the keypad or the dial pad on the touch screen when the phone is idle.

•

Tap the line key when the phone is idle to enter the dialing screen.

•

Enter the desired number using the keypad or the dial pad on the touch screen.

•

Tap 

Audio Call/Video Call 

soft key to place a Audio call or Video call.

Answering Calls using Audio Call/Video Call Option

To answer a video call:

When an incoming video call arrives, the touch screen will be displayed as given below:

1. These options are visible only if the firmware version is 58.80.196.8 or later.

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARSH VP710

Hama Freedom Operating Instruction preview
Freedom
Brand: Hama Pages: 12
Unify OpenStage SL4 professional HiPath Cordless... User Manual preview
OpenStage SL4 professional HiPath Cordless...
Brand: Unify Pages: 80
HIKVISION DS-KP8000-WHE1 Quick Installation Manual preview
DS-KP8000-WHE1
Brand: HIKVISION Pages: 2
Topcom Fidelity 160 User Manual preview
Fidelity 160
Brand: Topcom Pages: 76
EASY3CALL GIP300 User Manual preview
GIP300
Brand: EASY3CALL Pages: 40
Avaya 1150E User Manual preview
1150E
Brand: Avaya Pages: 237
Fisher-Rosemount HART 275 Product Manual preview
HART 275
Brand: Fisher-Rosemount Pages: 116
Aastra SIP SIP9133i User Manual preview
SIP SIP9133i
Brand: Aastra Pages: 22
NEC Docomo Foma N-08A Manual preview
Foma N-08A
Brand: NEC Docomo Pages: 27
Dartel LJ-68R User Manual preview
LJ-68R
Brand: Dartel Pages: 43
Ericsson KF 788 User Manual preview
KF 788
Brand: Ericsson Pages: 63
Pantech Burst Manual preview
Burst
Brand: Pantech Pages: 97
TECNO MOBILE LIMITED KG6k User Manual preview
KG6k
Brand: TECNO MOBILE LIMITED Pages: 41
Sonim XP5520 Bolt User Manual preview
XP5520 Bolt
Brand: Sonim Pages: 89
ORANGE RIO II User Manual preview
RIO II
Brand: ORANGE Pages: 88
Xiaomi Mi 11 Lite 5G NE User Manual preview
Mi 11 Lite 5G NE
Brand: Xiaomi Pages: 9
Asus ZENFONE T500 Installation Manual preview
ZENFONE T500
Brand: Asus Pages: 8
Asus Zenfone Max M1 User Manual preview
Zenfone Max M1
Brand: Asus Pages: 22

Brands by name

Popular brands

Load more brands