Matrix SPARSH VP710 User Manual Download Page 289

Page: 289 / 1046

Matrix SPARSH VP710 User Guide

281

•

Tap .

•

You can do the following:

•

Tap

Resolution & quality

to configure the resolution of the camera.

•

Tap

Advanced

and then tap

Manual exposure

to configure whether to use manual exposure.

Email

You can use

Email

application to access personal or business email account, and send/receive emails. Before

signing in email, you should configure the type of your email account.

Signing In Email

When launching the

Email

application for the first time, a wizard will be provided for you to set up the email account

step by step.

To sign in email:

•

Do one of the following:

•

Swipe left or right to go to the second idle screen.

Tap

to launch

Email

application.

•

Swipe left or right to go to the third idle screen.

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Matrix SPARSH VP710, User Manual, Page: 289 / 1046

Search results

Summary of Contents for SPARSH VP710

Reviews: