Matrix SPARSH VP710 User Manual Download Page 265 | Manualshive

Page: 265 / 1046

background image

Matrix SPARSH VP710 User Guide

257

Gallery

You can use Gallery application to view pictures/videos stored in internal SD card/USB flash drive or take pictures/
videos. You can also perform basic editing tasks on pictures or set the desired picture as the wallpaper. The
pictures/videos can be shared with friends via Bluetooth or email.

Viewing Pictures/Videos

To view pictures/videos:

•

Swipe left or right to go to the second idle screen.

•

Tap

to launch

Gallery

application.

•

By default, the pictures/videos are displayed as thumbnails in an albums arrangement mode.

•

Tap

Albums

(Optional).

You can tap

Albums/Locations/Times/People/Tags

to view the pictures/videos in different arrangement

modes.

•

Swipe left/right to view all albums if required.

«
...
263
264
265
266
267
...
»

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARSH VP710

Brand: Positron Pages: 84

Brand: Allview Pages: 108

Capsat TT-3060A

Brand: Thrane&Thrane Pages: 182

Brand: Ericsson Pages: 56

Brand: Archos Pages: 14

Brand: Centrality Pages: 59

Brand: E-MetroTel Pages: 8

Brand: CHI MEI Pages: 26

Brand: Micromax Pages: 64

Brand: Nokia Pages: 107

WIRELESSIP 5000

Brand: Hitachi Cable Pages: 132

Brand: Avvio Pages: 30

Brand: Zte Pages: 172

FireCell FC-555-024

Brand: EMS Pages: 2

Brand: Coolpad Pages: 46

Brand: Alcatel Pages: 2

Brand: Astell & Kern Pages: 22

Brand: Escene Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands