Matrix SPARSH VP710 User Manual Download Page 261 | Manualshive

Page: 261 / 1046

background image

Matrix SPARSH VP710 User Guide

253

Sharing Pictures/Videos/Audios

You can share pictures/videos/audios with other device via Bluetooth or email. Before sharing pictures/videos/
audios via Bluetooth, make sure the Bluetooth device is discoverable. The operating instructions on sharing
pictures, video and audios are the same, the following take sharing pictures as example.

To share picture(s) via Bluetooth:

•

Swipe left or right to go to the second idle screen.

•

Tap

to launch FileManager application.

•

Tap

Photos

in the

Local Storage

field.

If a USB flash drive has been connected to your phone, you can tap Photos in the USB Storage field to
view the pictures stored in USB flash drive.

Your pictures will display as a list.

•

Drag up and down to scroll through the files if required.

•

Tap the checkbox(es) before the desired picture(s).

•

Tap

.

«
...
259
260
261
262
263
...
»

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARSH VP710

Brand: Pantech Pages: 116

Brand: Palm Pages: 52

Brand: Yealink Pages: 38

Brand: Xiaomi Pages: 16

OpenStage SL4 professional HiPath Cordless...

Brand: Unify Pages: 80

Brand: Archos Pages: 115

Brand: T-Mobile Pages: 25

Brand: Avaya Pages: 6

ONE TOUCH Fierce

Brand: Alcatel Pages: 15

Brand: Alcatel Pages: 10

Brand: Akuvox Pages: 83

Brand: Docomo Pages: 228

Brand: Gplus Pages: 68

Brand: Salora Pages: 33

Brand: Grandstream Networks Pages: 1

Brand: Hisense Pages: 42

Brand: Fujitsu Pages: 32

Brand: Fujitsu Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands