Matrix Orbital GLK24064-25 Technical Manual Download Page 68 | Manualshive

Page: 68 / 68

background image

Command Summary

63

9

Definitions

ASCII: American standard code for information interchange used to give standardized numeric codes
to alphanumeric characters.

BPS:

Bits per second, a measure of transmission speed.

Byte: An unsigned data packet that is eight bits long.

DOW: Dallas One-Wire protocol, similar to I

2

C, provides reduced data rates at a greater distance. One

wire carries data, while two others supply power and ground. Matrix Orbital tests non-parasitic devices
only, those that do not draw power from the data line; however, some parasitic devices may work.

GPO: General purpose output, used to control peripheral devices from a display.

GUI:

Graphical user interface.

Hexadecimal: A base 16 number system utilizing symbols 0 through F to represent the values 0-15.

I

2

C:

Inter-integrated circuit protocol uses clock and data lines to communicate short distances at

slow speeds from a master to up to 128 addressable slave devices. A display is a slave device.

Integer: An unsigned data packet that is thirty-two bits long, in little Endian format.

LSB:

Least significant bit or byte in a transmission, the rightmost when read.

MSB: Most significant bit or byte in a transmission, the leftmost when read.

RS232: Recommended standard 232, a common serial protocol. A low level is -30V, a high is +30V.

RS422: Recommended standard 422, a more robust differential pair serial protocol.

SDA:

Serial data line used to transfer data in I

2

C protocol. This open drain line should be pulled high

through a resistor. Nominal values are between 1K and 10K Ω.

SCL:

Serial clock line used to designate data bits in I

2

C protocol. This open drain line should be pulled

high through a resistor. Nominal values are between 1K and 10K Ω.

Short: An unsigned data packet that is sixteen bits long, in little Endian format.

TTL:

Transistor-transistor logic applied to serial protocol. Low level is 0V while high logic is 5V.

10

Contact

Sales

Phone: 403.229.2737
Email:

[email protected]

Support

Phone: 403.204.3750
Email:

[email protected]

Online

Purchasing:

www.matrixorbital.com

Support:

www.matrixorbital.ca

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

«
...
66
67
68

Summary of Contents for GLK24064-25





































































Reviews:

No comments

Related manuals for GLK24064-25

Brand: Bang & Olufsen Pages: 9

Brand: Bang & Olufsen Pages: 12

Brand: Hach Pages: 86

Brand: BADLANDS Pages: 2

Brand: Fancom Pages: 31

Brand: 3M Pages: 90

Brand: +GF+ Pages: 3

Brand: Össur Pages: 58

Brand: Case IH Pages: 81

Brand: Delabie Pages: 20

Brand: Linear Technology Pages: 32

Brand: National Instruments Pages: 22

Brand: Manfrotto Pages: 2

Brand: Ublox Pages: 58

Brand: M-system Pages: 7

Brand: Foxconn Pages: 13

Brand: Eaton Pages: 94

Brand: G-Scale Graphics Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands