Matrix Orbital GLK24064-25 Technical Manual Download Page 10 | Manualshive

Page: 10 / 68

background image

Command Summary

5

2.3

USB Module

The GLK24064-25-USB/GLT24064-USB offers a single USB protocol for easy connection to a host
computer. The simple and widely available protocol can be accessed using the on board mini B style
USB connector as outlined in the USB Connections section.

Recommended Parts

Figure 5: Mini USB Cable

(EXTMUSB3FT)

The External Mini USB cable is recommended for the GLK24064-25-
USB/GLT24064-USB display. It will connect to the miniB style header on the
unit and provide a connection to a regular A style USB connector, commonly
found on a PC.

USB Connections

The USB connection is the quickest, easiest solution for PC development. After driver installation, the
GLK24064-25-USB/GLT24064-USB will be accessible through a virtual serial port, providing the same
result as a serial setup without the cable hassle. To connect to your GLK24064-25-USB/GLT24064-USB
please follow the steps below.

1.

Set the Protocol Select jumpers.



USB: The GLK24064-25-USB/GLT24064-USB offers USB protocol only. Model specific hardware
prevents this unit from operating in any other protocol, and does not allow other models to
operate in USB. Protocol Select jumpers on the USB model cannot be moved.

2.

Make the connections.



Plug the mini-B header of your External Mini USB cable into your GLK24064-25-USB/GLT24064-
USB and the regular USB header into your computer USB jack

*

.

3.

Install the drivers.
a.

Download the latest drivers at

www.matrixorbital.ca/drivers

, and save them to a known

location.

b.

When prompted, install the USB bus controller driver automatically

c.

If asked, continue anyway, even though the driver is not signed

d.

When the driver install is complete, your display will turn on, but communication will not yet be
possible.

e.

At the second driver prompt, install the serial port driver automatically

f.

Again, if asked, continue anyway

4.

Create.



Use MOGD# or a terminal program to get started, and then move on with your own
development. Instructions for the former can be found below and a number of application
notes are available for the latter at

www.matrixorbital.ca/appnotes

.

*Note:

The YG version of the GLK24064-25-USB/GLT24064-USB

will require the alternate power connection.

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

«
...
8
9
10
11
12
...
»

Summary of Contents for GLK24064-25





































































Reviews:

No comments

Related manuals for GLK24064-25

TLE Scalable 150

Brand: GE Pages: 6

Brand: GE Pages: 3

Brand: GE Pages: 80

PACSystems* RX3i

Brand: GE Pages: 39

PACSystems* RX3i

Brand: GE Pages: 35

PACSystems* RX3i

Brand: GE Pages: 3

PACSystems* RX3i

Brand: GE Pages: 169

PACSystems RX7i

Brand: GE Pages: 317

Brand: EA Pages: 24

Brand: V2 ELETTRONICA Pages: 72

Brand: Mackie Pages: 16

Brand: TANDBERG Pages: 47

Brand: Multi-Clean Pages: 4

Brand: Primo Water Pages: 10

Brand: PENGWYN Pages: 32

Brand: Warner Electric Pages: 6

Brand: HEROSE Pages: 92

Brand: Kohzu Precision Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands