background image

 

List of illustrations 

Page 18 

 

 

10 

List of illustrations 

Fig. 1: Adjusting the coupling triangle ....................................................................................................... 6

 

Fig. 2: Locking pin on the coupling triangle ............................................................................................... 7

 

Fig. 3: Connecting the hydraulic lines on the tractor hydraulic system ....................................................... 7

 

Fig. 4: Adjust slide runner......................................................................................................................... 8

 

Fig. 5: Secure slide runner ....................................................................................................................... 8

 

Fig. 6: Secure telescopic foot ................................................................................................................... 8

 

Fig. 7: Fastening screws - attachment bracket .......................................................................................... 9

 

Fig. 8: Adjust the length of contact angle - set screw ................................................................................ 9

 

Fig. 9: Adjusting the pendulum compensation ........................................................................................ 10

 

Fig. 10: Pendulum plate ......................................................................................................................... 11

 

Fig. 11: Adjust the pressure control valve. .............................................................................................. 11

 

Fig. 12: Nameplate................................................................................................................................. 13

 

Fig. 13: Lubricating nipple - cylinder eyes ............................................................................................... 14

 

Fig. 14: Lubricating nipple - piston rod eye ............................................................................................. 15

 

Fig. 15: Lubricating nipple - pendulum axle ............................................................................................ 15

 

Fig. 16: Swing axle of the snow blade .................................................................................................... 15

 

 

Summary of Contents for SRM-SF 140




















Reviews: