background image

 

Operation 

 

 

Page 17 

   

 

Fig. 21: Broom and shovel holder 

Fig. 22: Broom and shovel lock 

Operation 

 

Danger! 
Severe injury to the operator or third parties occurs.  
The load distribution on the trailer changes due to the attached spreader. 
Steering and braking capability, as well as tilt behavior are influenced. 
Initiate countermeasures - ensure sufficient front wheel ballast! 

 

Danger! 
Severe injury to the operator or third parties occurs.  
Never reach into the area of the agitator. Switch off the tractor and remove 
the ignition key before reaching into the area of moving parts. Make sure that 
the safety grille is always attached during operation. 

 

Attention! 
Increased risk of accident due to rotating PTO shaft. 
Do not enter the work area of the PTO shaft until it has stopped rotating. 
Do not wear baggy or loose clothing that could get caught in the PTO shaft. 

5.1 

Parking the box spreader 

Park the box spreader on a level and paved surface and only when the container is 
empty 

5.2 

Filling the box spreader 

Before filling the box spreader, connect the spreader to the tractor and lower the tractor’s 

rear hydraulic unit and set the spreader on the ground. Shut off the tractor engine, 
remove the key from the ignition and set the hand brake. Before filling the spreader 
container, always check for foreign objects. The gate valve must also be checked 
regularly to ensure it is functioning properly.  

Summary of Contents for SPR-HM-100






























Reviews: