AU SUPPORT 1800 237 425 WWW.MATCHMASTER.COM.AU | NZ SUPPORT 0800 237 425 WWW.MATCHMASTER.CO.NZ PAGE | 1 OF 2
34MM-HDS2
INSTRUCTION MANUAL
STATEMENT
FEATURES
PANEL DESCRIPTION
DIP SWITCH OPERATION
SAFETY PRECAUTION
AFTER-SALES SERVICE
PACKING LIST
PRODUCT INTRODUCTION
Thanks for purchasing this product, please read this user
manual carefully before using this product. The functions
described in this version are updated till July, 2019. In the
constant effort to improve our product, we reserve the right
to make functions or parameters changes without notice or
obligation.
We provide limited warranty for the product
within three years.
• 1x HDMI 2.0 1x2 Splitter
• 4x Plastic Cushions
• 1x Power Adapter (5V DC 1A)
• 1x User Manual
Note:
Please contact your distributor immediately if any damage or defect in
the components is found.
• Do not dismantle the housing or modify the module to
avoid electrical shock or burn.
• Using supplies not meeting the products’ specifications
may cause damage, deterioration or malfunction.
• Do not expose the unit to rain, moisture or install this
product near water.
• Install the device in a place with fine ventilation.
• Do not twist or pull by force ends of the optical cable.
It can cause malfunction.
• Do not use liquid or aerosol cleaners to clean this unit.
• Always unplug the power to the device before cleaning.
• Unplug the power when not used for a long period of time.
• Refer all servicing to qualified service personnel.
Thanks for choosing the HDMI 2.0 1x2 Splitter, which can
distribute one HDMI input to two outputs. The splitter
supports HDMI video resolution up to 4K@60Hz 4:4:4,
1080p 3D, and multichannel audio formats. Besides passing
EDID information from the display, there are multiple built-in
EDID settings can be selected by the 4-pin DIP switch on
the front panel. Moreover, the splitter supports convenient
firmware upgrade through Micro-USB port.
• Supports HDMI 2.0 and the video resolution up to
4K@60Hz 4:4:4.
• HDMI input supports HDCP 2.3 and the outputs support
HDCP Active or HDCP Passive mode.
• Supports video resolution down-scaling, the 4K input
can be automatically degraded to 1080p output for
compatibility with 1080p display.
• 18Gbps high bandwidth.
• Advanced EDID management: multiple built-in EDID
settings can be selected.
• Built-in equalizer for signal enhancement to avoid signal
attenuation in transmission.
• Supports CEC pass-through.
• Provides LEDs to indicate the current operating status.
• Firmware upgrade by Micro-USB port.
Front Panel
EDID Management
Rear Panel
1
2
3
4
5
1. POWER LED: The LED illuminates red when
2. power is applied.
3. INPUT LED: The LED illuminates blue when
4. there is HDMI input.
5. OUTPUT LEDs: The LED illuminates blue when there is
HDMI output on the corresponding channel.
6. EDID: 4-pin DIP switch for EDID setting and HDCP mode
selection. Please refer to the EDID Management for
more details.
7. FW: Micro-USB port for firmware upgrade.
1. INPUT: Type-A female HDMI input port to connect
a HDMI source.
2. OUTPUTS: Two type-A female HDMI output ports
to connect HDMI displays.
3. DC 5V: DC barrel port to connect an AC power adapter.
1
2
3
IN
OUT 1
OUT 2
DC 5V
The Extended Display Identification Data (EDID) is used
by the source device to match its video resolution with the
connected display. By default, the source device obtains
its EDID from the first connected display. Meanwhile, since
the displays with different capabilities are connected to the
splitter, the DIP switch on the front panel can be used to
set the EDID to a fixed value to ensure the compatibility in
video resolution.The switch represents “
0
” when in the lower
(
OFF
) position, and it represents “
1
” while putting the switch
in the upper (
ON
) position.
