LISTED
This symbol designates that this tool is listed with
U.S. requirements by ETL Testing Laboratories, Inc.
Conforms to UL Std. 60745-1.
3042597
JD3312U
Engraver
167396
Operating Instructions
GENERAL SAFETY RULES
WARNING
: Read and understand all instructions.
Failure to
follow all instructions listed below may result in electric shock, fire and/or
serious personal injury.
WARNING:
This product contains chemicals known to the
State of California to cause cancer, birth defects and/or
reproductive harm.
WORK AREA
Keep your work area clean and well lit. Cluttered benches and dark areas
invite accidents.
Do not operate power tools in potentially explosive environments, such
as in the presence of flammable liquids, gas or dust. Power tools create
sparks that may ignite dust or fumes.
Keep bystanders, children and visitors away while operating the tool.
Distractions can cause the operator to lose control.
ELECTRICAL SAFETY
Double insulated tools are equipped with a polarized plug (one blade is
wider than the other).
This plug will only fit into a polarized plug one way.
If the plug does not fit into the outlet properly, reverse the plug.
If it still
does not fit, contact a qualified electrician to install a polarized outlet. Do
not alter the plug in any way.
Double insulation eliminates the need for
the three-pronged grounded power cord and grounded power supply
system.
Avoid contact between the operator's body and grounded surfaces such
as pipes, radiators, ranges, and refrigerators. There is an increased risk
of electric shock if the operator's body is grounded.
Do not expose power tools to rain or wet conditions. Water entering the
power tool will increase the risk of electric shock.
Do not abuse the cord. Do not use the power cord to carry the tool or to
pull the plug out of the outlet. Keep the power cord away from heat, oil,
sharp edges, and moving parts. Replace a damaged power cord
immediately. A damaged power cord increases the risk of electric shock.
When operating a power tool outdoors, use an outdoor-rated extension
cord type
"W-A" or "W". These cords are rated for outdoor use and they reduce the
risk of electric shock.
PERSONAL SAFETY
Stay alert, be aware of the surroundings, and use common sense when
operating a power tool. Do not use a power tool while tired or under the
influence of drugs, alcohol, or medication. A moment of inattention while
operating a power tool may result in serious personal injury.
Dress properly.
Do not wear loose clothing or jewelry.
Contain long hair. Keep hair, clothing, and gloves away from moving
parts. Loose clothing, jewelry, or long hair can get caught in moving
parts.
Avoid accidental start-ups. Verify that the switch is in the OFF position
before plugging in the tool. Carrying a power tool with a finger on the
switch or plugging in a tool that has the switch in the ON position invites
accidents.
Remove adjusting keys and wrenches before turning the tool ON. A
wrench or key that is left attached to a rotating part of the tool may result
in personal injury.
Do not overreach. Keep proper footing and balance at all times. Proper
footing and balance allows the operator to maintain better control of the
tool in unexpected situations.
Use safety equipment. Always wear eye protection.
Use a dust mask, non-skid safety shoes, a hardhat, or hearing protection
when appropriate.
USE AND CARE OF POWER TOOLS
Use clamps or another practical means to secure and support the
workpiece to a stable platform. Holding the work in a hand or against the
body is not stable, and may lead to loss of control.
Do not force the tool. Use the correct tool for the application. The correct
tool will do the job better and safer when used at the rate that it was
designed to work at.
Do not use a power tool if it cannot be turned ON or OFF using the power
switch. A tool that cannot be controlled using the switch is dangerous,
and must be repaired.
Disconnect the plug from the outlet before making any adjustments,
changing accessories, or storing the tool. Such preventive safety
measures reduce the risk of accidental start-ups.
When power tools are not in use, store them out of the reach of children
or untrained persons. Tools are dangerous in the hands of untrained
users.
Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less likely to bind,
and are easier to control.
Inspect the tool for misalignment or binding of moving parts, broken
parts, and any other condition that may affect the operation of the tool. If
it is damaged, have the tool serviced
before using it.
Many accidents
are caused by poorly maintained tools.
Use only accessories that are recommended by the manufacturer for this
model. Accessories that are suitable for one tool may become hazardous
when used with another tool.
KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE
PRODUCT SPECIFICATIONS
Rating:
120 V, 60 Hz AC
Amperes:
0.2 A
Continuous
operating time:
5 minutes maximum between
complete cool down cycles
Engraving bit:
Tungsten carbide tipped steel
Tool weight:
13 oz. (0.37 kg)
Need Assistance?
Call us on our toll free customer support line:
1-866-349-8665 Monday
– Friday from
9am to 5pm Eastern Standard Time
Technical questions
Replacement parts
Parts missing from package
!
!
