background image

 

 

MASTER-BILT PART NUMBERS

   

 
The table below gives Master-Bilt part numbers.  Use this chart when ordering replacement parts for your 

MPM/QMPM

 cases. 

 

All quantities are one each unless otherwise noted by parentheses

 

Description MPM-36 

QMPM-36 

MPM-48 

QMPM-48 

MPM-72 

QMPM-72 

Anti-Sweat Heater-Side 

17-09121 

17-09122 

17-09130 

Anti-Sweat Heater-Front 

17-09119 

17-09120 

17-09131 

Condensate Pan Heater 

17-09140 

17-09140 

17-09140 

Condensing Unit 

03-14234 

01-01474 

01-01477 

Drier 

09-09309 

09-09307 

09-09185 

Evaporator Coil 

07-13102 

07-13103 

07-13106 

Evaporator Fan Blade 

15-01184 

15-01184 

15-01184 

Evaporator Fan Motor 

13-00685 

13-00685 

13-00685 

Expansion Valve 

 

 

09-09548 

Female Plug 

21-00577 

21-00577 

21-00577 

Power Cord 

21-00312 

21-01218 

 

Temperature Control 

19-13092 

19-13092 

19-13092 

Timer 

19-00819 

19-00819 

19-00819 

Toggle Switch 

19-01090 

19-01090 

 

 

ACCESSORIES LIST 

 

PART NO. 

DESCRIPTION 

SHIP WT. 

LB/KG 

 

BUMPER KITS 

 

A071-00100 

White bumper for QMPM-36, QMVM-36 and QMVM-36L 

5/2 

A071-00200 

Red bumper for QMPM-36, QMVM-36 and QMVM-36L 

5/2 

A071-00300 

Green bumper for QMPM-36, QMVM-36 and QMVM-36L 

5/2 

A071-00400 

Blue bumper for QMPM-36, QMVM-36 and QMVM-36L 

5/2 

A071-00500 

Brown bumper for QMPM-36, QMVM-36 and QMVM-36L 

5/2 

A071-00600 

Black bumper for QMPM-36, QMVM-36 and QMVM-36L 

5/2 

A072-00100 

White bumper for QMPM-48, QMVM-48 and QMVM-48L 

5/2 

A072-00200 

Red bumper for QMPM-48, QMVM-48 and QMVM-48L 

5/2 

A072-00300 

Green bumper for QMPM-48, QMVM-48 and QMVM-48L 

5/2 

A072-00400 

Blue bumper for QMPM-48, QMVM-48 and QMVM-48L 

5/2 

A072-00500 

Brown bumper for QMPM-48, QMVM-48 and QMVM-48L 

5/2 

A072-00600 

Black bumper for QMPM-48, QMVM-48 and QMVM-48L 

5/2 

A073-00100 

White bumper for QMPM-72 and QMVM-72 

5/2 

A073-00200 

Red bumper for QMPM-72 and QMVM-72 

5/2 

A073-00300 

Green bumper for QMPM-72 and QMVM-72 

5/2 

A073-00400 

Blue bumper for QMPM-72 and QMVM-72 

5/2 

A073-00500 

Brown bumper for QMPM-72 and QMVM-72 

5/2 

A073-00600 

Black bumper for QMPM-72 and QMVM-72 

5/2 

Summary of Contents for MPM-36

















Reviews: