manualshive.com logo in svg

Mastech ms8261, Operator'S Instruction Manual

Share
Download
Mastech ms8261 Operator'S Instruction Manual Download Page 1

HANDHELD

DIGITAL MULTIMETER

OPERATOR’S

INSTRUCTION MANUAL

GENERAL INSTRUCTIONS

This instrument complies with IEC 1010-1 (61010-1@IEC: 2001), CAT. II 1000V and CAT. III 600V

overvoltage standards. See Specifications.

To get the best service from this instrument, read carefully this user's manual and respect the detailed

safety precautions.

International symbols used on the Meter and in this manual are explained in chapter 1.1.3

Precautions safety measures

1.1.1 Preliminary

* Measurement category III is for measurements performed in the building installation.

NOTE: Examples are measurements on distribution boards, circuit-breakers, wiring, including cables,

bus-bars, junction boxes, switches, socket-outlets in the fixed installation, and equipment for industrial

use and some other equipment, for example, stationary motors with permanent connection to the fixed

installation.

* Measurement category II is for measurements performed on circuits directly connected to the low

voltage installation.

NOTE: Examples are measurements on household appliances, portable tools and similar equipment.

* Measurement category I is for measurements performed on circuits not directly connected to MAINS.

NOTE: Examples are measurements on circuits not derived from MAINS, and specially protected

(internal) MAINS derived circuits. In the latter case, transient stresses

are variable; for that reason, requires that the transient withstand capability of the equipment is made

known to the user.

* When using this Multimeter, the user must observe all normal safety rules concerning:

― protection against the dangers of electric current.

― protection of the Multimeter against misuse.

* For your own safety, only use the test probes supplied with the instrument. Before use, check that they

are in good condition.

1.1.2 During use

* If the meter is used near noise generating equipment, be aware that display may become unstable or

indicate large errors.

* Do not use the meter or test leads if they look damaged.

* Use the meter only as specified in this manual; otherwise, the protection provided by the meter may be

impaired.

Summary of Contents for ms8261















Reviews:

No comments

Brands by name

Popular brands

Load more brands