Masport Geneva Owners & Installation Manual Download Page 1

FOR YOUR SAFETY
What to do if you smell gas:

!

!

!

!

!

Do not try to light any ap-
pliance

!

!

!

!

!

Do not touch any electri-
cal switch: do not use any
phone in your building.

!

!

!

!

!

Immediately call your gas
supplier from a neigh-
bour's phone. Follow the
gas supplier's instruc-
tions.

!

!

!

!

!

If you  cannot reach your
gas supplier, call the fire
department.

WARNING:
Improper installation, adjustment, altera-
tion, service or maintenance can cause
injury or property damage. Refer to this
manual. For assistance or additional infor-
mation consult an authorized installer, serv-
ice agency or the gas supplier.

FOR YOUR SAFETY
Do not store or use gasoline or other flam-
mable vapours and liquids in the vicinity of
this or any other appliance.

Installation and service must be performed
by an authorized installer, service agency or
the gas supplier.

PLEASE KEEP THESE INSTRUCTIONS

FOR FUTURE REFERENCE

Owners &
Installation

Manual

LISTINGS AND CODE
APPROVALS

These gas appliances have been
tested in accordance with AG
103, NZS 5262 and have been
certified by the Australian Gas
Association for installation and
operation as described in these
Installation and Operating
Instructions.

Your unit should be serviced
annually by an authorised
service person.

Models: F43-NG

Natural Gas

F43-LP

Propane

F28-NG

Natural Gas

F28-LP

Propane

02/01/01

Geneva /Ultimate

Head Office - Australia
54 Boundary Rd. Braeside
P.O. Box 553
Mordialloc   3195
Ph.   (03) 9586-7777
Fax. (03) 9586-2980

Head Office - New Zealand
1-37 Mt  Wellington Hwy.Panmure,
P.O. Box 14349
Auckland 6.
Ph.  (9) 570-9009
Fax. (9) 527-1294

908-061

(Australia)                         (New Zealand)

Summary of Contents for Geneva



























Reviews: