manualshive.com logo in svg

Masoneilan SVI II ESD, Installation And Maintenance Manual

Share
Download
Masoneilan SVI II ESD Installation And Maintenance Manual Download Page 199

Masoneilan SVI II ESD Installation and Maintenance Manual 

=

|

 

199

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.

Modem and Computer Use in Intrinsically Safe Circuits

Many HART

®

 modems in use today are not approved for connecting to Intrinsically Safe 

control circuits. Most portable computers are NOT approved for use in hazardous areas. 
Modems can be safely connected to the safe area side of barriers, and isolators. Observe 
HART

®

 filter requirements.

MACTek

®

 Intrinsically Safe modem, Model 010005

The VIATOR RS232 HART

®

 Interface [Eex ia] IIC complies with the Essential Health and Safety 

Requirements relating to the design and construction of equipment and protective systems 
intended for use in potentially explosive atmospheres. Requirements given in Annex II of the 
Directive 94/9/EC (ATEX Directive) of the European Parliament and EU Council of 23rd March 
1994. Consult MACTek Corporation, http://www.MACTekcorp.com/company.html for detailed 
requirements for safe use.

MACTek

®

 Warning

 

"This product has not been tested by any certification agency such as Factory Mutual with 
jurisdiction outside the European Union for intrinsic safety. The product can be used outside 
the European Union (e.g. in the USA) on the sole authority of the buyer. MACTek

®

 makes no 

claims of suitability and offers no warranties regarding the use of this product for connection 
of PCs to circuits extending into hazardous areas in countries outside the European Union." 

Do not connect a PC or HART

®

 modem to an intrinsically safe circuit except on the safe area 

side of a barrier. Do not operate a PC in a hazardous area without compliance with local and 
plant regulations.

Use of Hand-held Communicators In Intrinsically Safe Circuits

WARNING

The DPI 620 is not approved for use in hazardous areas that use 
explosion proof safety practices. Do not use the DPI 620 unless 
the area has been declared safe (Hot Work Permit).

The HART

®

 Communicator DPI 620 is approved to communicate with intrinsically safe control 

circuits in hazardous areas. Read the product Manual for the HART

®

 Communicator. Observe 

all warnings. The intrinsic safety entity parameters must be added to the SVI II ESD entity 
parameters to determine suitability for use in any intrinsically safe circuit. Observe the labels 
on the DPI 620 or consult the manufacturer.

Summary of Contents for SVI II ESD





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands