manualshive.com logo in svg

Masoneilan SVI II ESD, Installation And Maintenance Manual

Share
Download
Masoneilan SVI II ESD Installation And Maintenance Manual Download Page 17

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.

Masoneilan SVI II ESD Installation and Maintenance Manual 

=

|

 

17

1. Safety Information

Introduction

This section provides information necessary to design, install, verify and maintain a Safety 
Instrumented Function (SIF) utilizing a Masoneilan Smart Valve Interface, SVI II ESD. This manual 
provides necessary requirements for meeting the IEC 61508 or IEC 61511 functional safety 
standards.

Terms and Abbreviations

The following terms and abbreviations are related to safety functions of the SVI II ESD and are 
used throughout this document.

Safety

Freedom from unacceptable risk of harm.

Functional 
Safety

The ability of a system to carry out the actions necessary to achieve or to main-
tain a defined safe state for the equipment / machinery / plant / apparatus 
under control of the system.

Basic Safety

The equipment must be designed and manufactured such that it protects 
against risk of damage to persons by electrical shock and other hazards and 
against resulting fire and explosion. The protection must be effective under all 
conditions of the nominal operation and under single fault condition.

Safety 
Assessment

The investigation to arrive at a judgment - based on evidence - of the safety 
achieved by safety-related systems.

Fail-Safe State

State where the SVI II ESD is de-energized and has exhausted Actuator 1 in a sin-
gle acting configuration or has caused Actuator 1 to be at an equal or lower 
pressure than Actuator 2 in a dual acting configuration.

Fail Safe

Failure that causes the valve to go to the defined fail-safe state without a 
demand from the process.

Fail Dangerous

Failure that does not respond to a demand from the process (i.e. being unable to 
go to the defined fail-safe state).

Summary of Contents for SVI II ESD





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands