Home
/
Masoneilan
/
SVI II ESD
/
Installation And Maintenance Manual

Masoneilan SVI II ESD, Installation And Maintenance Manual

Share

Page: 114 / 220

Masoneilan SVI II ESD Installation And Maintenance Manual Download Page 114

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.

114

|

BHGE

PST CONF (VIEW DATA) Menu

There are two instances of PST CONF (PST CONFiguration) contained in the display menus; one
instance can only be accessed from VIEW DATA, the other instance is accessed through
SETUP. PST CONF only displays the PST configuration data when accessed from VIEW DATA.

NOTE

If you would like to configure Partial Stroke Testing (PST) refer to
“PST Configuration” on page 122.

The PST configuration parameters viewable by pressing

+

and

-

are:

TRAVEL

PMIN

: Pressure Units (PSI, BAR, KPA)

MAX TIME

RAMPSPEED

Viewing PST Configuration Parameters

To view PST configuration parameters use the following procedure:

1. If in NORMAL operating mode, press any button.

2. Press

+

to move through the options until you reach VIEW DATA menu item.

3. Press

*

to go to VIEW DATA menu (This leaves the valve in NORMAL mode.). If in MANUAL

mode, press

+

repeatedly until VIEW DATA menu item is reached. Press

*

to select VIEW

DATA mode.

4. In VIEW DATA menu, press

+

repeatedly until the PST CONF menu item is reached. Press

*

to select PST CONF mode.

«
...
112
113
114
115
116
...
»

Summary of Contents for SVI II ESD





























































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands