manualshive.com logo in svg

Maserati Quattroporte, Owner'S Manual

Share
Download
Maserati Quattroporte Owner'S Manual Download Page 41

2

39

Understanding the Vehicle

for rear seat passengers (see “Rear
Seats” in this section).

A 12 V power outlet both inside the
central console and in the rear of the
reclining shelf, are available for rear
seats passengers (see "Comfort Luxury
Rear Seats" in this section).

"Comfort Luxury" Rear Seats

"Comfort Luxury" Rear Seats

Power Outlet inside the Boot

The power outlet is positioned on the
right side of the boot compartment.

Cup Holders

The vehicle is equipped with several
cup holders.

CAUTION!

•

Use light and shatterproof
containers.

•

Do not forcefully push unsuitable
containers into the cup holders to
prevent damage to the containers.

•

Do not store hot drinks.

Cup Holders for Front Passengers

The front cup holders are located
beside the transmission lever and may
be with access cover or at sight (

,

only for left-hand drive version).
To access the cup holder, push the
cover as shown in the picture and it
will open completely.

Version with Cover

Summary of Contents for Quattroporte









































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands