Maserati Quattroporte Owner'S Manual Download Page 222

Page: 222 / 328

220

Driver Assistance Systems

System Controls and Activation
Conditions

The buttons on steering wheel RH side
control ACC operation and the other
functions/driver assist systems installed
to this vehicle.

Multifunction control shared by
all driver assist functions/systems:
- Press up (indication "RES +"):

increase speed, set current speed
or resume previously set speed
when system is in "cancelled"
status.

- Pushed (indication "CANC"):

cancel the function if it was in
"set" status, going in a ready
condition but remembering the
previous set speed.

- Press down (indication "SET -"):

set speed/decrease speed.

Two functions button with ACC
activated:

- ACC time gap: pressed and

released; set the distance
to sensed vehicle ahead as
horizontal bars (setting cycle
starts to 3 bars).

- CC On: pressed for 2 seconds

activates the CC system. See
chapter "Cruise Control - CC" in
this section for further details.

- Press it to switch from CC to ACC.

ACC ON/OFF button. If enabled,
pressing this button will disable
CC.

ADA ON/OFF button

with ACC set

only. See "Active Driving Assist -
ADA" in this section for further
details.

NOTE:

Any change made to tire dimensions
affects performance of Adaptive Cruise
Control and Front Collision Warning.

The ACC is not activated in the
following conditions:
• When braking.
• When parking brake is activated.
• When automatic transmission is in P

(Park), R (Reverse) or N (Neutral).

• When vehicle speed is out of preset

speed range.

• When brakes are overheated.
• When driver door is open.

• When the driver’s seat belt is

unbuckled.

• When the road is particularly steep

(both uphill and downhill) at low
speed.

• When drive mode

(ESC OFF) is

selected.

• When the door is opened at low

speed.

• When there has been an ESC event in

the last 5 seconds, or is still active.

• When there is an object too close in

front of the vehicle.

It is possible that more than one
system is active at the same time such
as ACC and ABSA just to mention
some.
While activation of ACC and CC at the
same time is impossible.

Speed Range of Use

Speed

km/h (mph)

Minimum

Engaged/activated

30 (20)

Maximum

210 (130)

Activation/Deactivation

NOTE:

Pictures show status of ACC and LKA
systems.

Summary of Contents for Quattroporte









































































































































































































































































































































Search results

Summary of Contents for Quattroporte

Reviews:

Brands by name

Popular brands

Maserati Quattroporte, Owner'S Manual

Search results

Summary of Contents for Quattroporte

Reviews:

Brands by name

Popular brands