background image

12

m

WARNING!

 Before performing any maintenance, always 

disconnect the power supply to the unit and wait until the tine 

cylinder comes to a complete stop. Wear protective gloves 

when handling the tines.

1.  Remove the thatch collection bag.
2.  Place the machine upside down on a flat stable surface to 

access the underbody.

3.  Loosen the two bolts with a suitable wrench, remove them 

together with the spring washers and the attached cutting 

device (Fig. 14).

4.  To remove the cutting device, first lift the bearing and then 

pull it out from the drive shaft.

5.  Align and insert the respective cutting device: Slide the 

hex nut into the socket of the drive shaft and fix the 

bearing to the support with the bolts and spring washers  

(Fig. 15).

NOTE: If you have any questions, please call the Snow Joe

®

 

+ Sun Joe

®

 customer service center at 1-866-766-9563 

(1-866-SNOWJOE) for assistance.

After Use

1.  Switch the machine off, disconnect it from the power 

supply and let it cool down.

2.  Check, clean and store the machine as described below.

Thatch Collection Bag

1.  Inspect the thatch collection bag before each use. Do not 

use it if you find any damage.

2.  Clean the thatch collection bag after operation. Let the 

thatch collection bag dry thoroughly before storing to 

avoid mildew.

Transportation

1.  Switch the product off and disconnect it from power 

supply before transporting it anywhere.

2.  Attach transportation guards, if applicable.
3.  Adjust the cutting depth to the transportation stage (refer 

to “CUTTING DEPTH ADJUSTMENT” on page 9).

4.  Always transport the product by its handle.
5.  Protect the product from any heavy impact or strong 

vibrations which may occur during transportation in 

vehicles.

6.  Secure the product to prevent it from slipping or falling over.

Fig. 14

2 bolts +  

spring washers

Cutting device

(scarifying cylinder)

Fig. 15

Cutting device

(raking cylinder)

Summary of Contents for MTS-DTS13

















Reviews: