Marshall Electronics VS-547-3GSDI Page 17 User Manual Download

Page: 17 / 74

Remote Configuration

User Manual VS-547-3GSDI – V1.0

Page 17 of 74

3/2016

Audio



Algorithm

Select the Audio Algorithm:

G.711

AAC.

G.711 and AAC is supported from client

to camera direction. However, bi-directional audio communication is supported.



Bitrate

Bitrate ranges from 64Kbps and 128kbps when AAC is selected. The sample rate is
fixed to 8KHz and 32KHz for G.711 and AAC respectively. Note: when the camera
is connected to a decoder, the decoder

’s audio algorithm should be set identically to

transmit the audio properly.



Mode

Select the Audio Operation Mode:

Mode

Action

Off

No Operation

Tx-Only

Transmit Only

Rx-Only

Receive Only

Tx & Rx

Transmit and Receive



Input Gain

Audio Input Gain ranges from 0 to 31.

Summary of Contents for VS-547-3GSDI











































































Search results

Summary of Contents for VS-547-3GSDI

Reviews:

Related manuals for VS-547-3GSDI

Brands by name

Popular brands

Marshall Electronics VS-547-3GSDI, User Manual

Search results

Summary of Contents for VS-547-3GSDI

Reviews:

Related manuals for VS-547-3GSDI

Brands by name

Popular brands