Marshall Electronics QVW-1708 Operating Instructions Manual Download Page 18 | Manualshive

Page: 18 / 32

background image

18

OSD Configuration Submenu

Use the OSD Configuration submenu to select a variety of information to be displayed on the screen.

■

IMD State

Use this setting to enable or disable the IMD text display. This setting affects both the fixed string (entered through
display menus) and remote IMD text commands.

■

Status Display

Use this setting to enable or disable status display. When enabled, the current video input standard is displayed on the
top left of the screen. When disabled, status is only displayed for 2 seconds when the monitor is powered on, when an
input is applied, or when the input video standard changes. The status display reads “No Input” when no video input is
present.

OSD Configuration Submenu

Status Display

«
...
16
17
18
19
20
...
»

Summary of Contents for QVW-1708

































Reviews:

No comments

Related manuals for QVW-1708

Brand: Weldex Pages: 2

VPPE-3-1-1/8-x-E1 Series

Brand: Festo Pages: 2

UltraView AP-10AV Series

Brand: I-Tech Pages: 28

Brand: Unicont SPb Pages: 16

Brand: Hanwha Vision Pages: 4

Brand: ViewSonic Pages: 26

Brand: YAKUMO Pages: 23

Brand: Plura Pages: 46

Brand: ViewSonic Pages: 53

Brand: Quanmax Pages: 32

Brand: ViewSonic Pages: 22

Brand: Tatung Pages: 47

Brand: Evelo Pages: 8

Vision Master Pro 450

Brand: Iiyama Pages: 58

Brand: NEC Pages: 37

Brand: Panasonic Pages: 67

Brand: Panasonic Pages: 52

Brand: NEC Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands