Marshall Electronics QVW-1708 Operating Instructions Manual Download Page 10 | Manualshive

Page: 10 / 32

background image

10

On Screen Menu

Access and navigate the main menu using the RotoMenu

™

knob:

Using the RotoMenu knob

•

Press the

RotoMenu

™

knob to enter the main menu.

•

Rotate the knob to scroll up or down in the main menu or each submenu.

•

Press the

RotoMenu

™

knob to enter a submenu or choose a setting.

•

To return to main menu from submenu, select ‘Back’ and press the

RotoMenu

™

.

The menu timeout can be set in the OSD Timeout section of the OSD Config submenu.

Making Changes to an Individual Channel

The Quad-Viewer RotoMenu allows for Video, Color, System, OSD and IMD Configuration changes to be made to
individual channels in the Quad-Viewer system. Items in the menu that can be changed for each individual channel will
have a A1, A2, B1, B2 indicator on the right side of the menu and a small white box for each individual channel, as shown
below:

Main Menu

«
...
8
9
10
11
12
...
»

Summary of Contents for QVW-1708

































Reviews:

No comments

Related manuals for QVW-1708

Brand: GE Pages: 24

Corometrics 250cx Series

Brand: GE Pages: 250

732N - LCD Analog Display

Brand: Samsung Pages: 79

2243WM - SyncMaster - 22" LCD Monitor

Brand: Samsung Pages: 18

2233RZ - Syncmaster 22" 3D Gaming LCD Monito

Brand: Samsung Pages: 54

943BWX - SyncMaster - 19" LCD Monitor

Brand: Samsung Pages: 71

LC-M44-DFHD-120

Brand: LC-POWER Pages: 63

Brand: Planar Pages: 16

Brand: Monoprice Pages: 18

Brand: V7 Pages: 1

Brand: Polar Electro Pages: 2

Brand: TV Logic Pages: 48

Brand: G-STORY Pages: 41

Brand: AOR Pages: 39

Brand: Axis Pages: 22

Brand: Deif Pages: 2

Brand: NEC Pages: 50

Brand: Sansui Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands