MARMON ANGELO PO COMBISTAR FX Technical Manual Download Page 105

Page: 105 / 178

Copyright by Servizio Clienti ANGELO PO Spa

105

4.8. Gas alarms

GAS alarm table

Alarm Code

PROBLEM

SOLUTION

E12:F4

The blower fan is working but there is no ignition

spark

1. Check the wirings on the igniter and on

the spark plug.

2. Check the continuity of the HF cable.

3. Check the spark plug ground

connection

4. Dismantle the spark plug and check

the electrodes.

5. Check the power supply to the igniter.

6. Replace the igniter.

The blower fan is working and the spark is good

but there is no flame ignition.

1. Check the inlet gas pressure.

2. Check gas nozzle

3. Increase gas pressure regulation

(PR.ADJ.) until the burner ignition. (see
section 4.4.4.1)

4. Check gas pipe fixing

5. Check gas valve power supply

6. Check that the outlet pressure of the

gas is free

7. Clean the blower fan air intake

Detonation at the ignition

1. Dismantle and check the spark plug.

2. Check combustion and gas

parameters.

The flame is lighting but after some seconds the

flame goes off.

1. verify the flame detector cable

2. verify the correct power connection

(see chapter 4.2.5.)

3. replace the flame detector and/or the

combustion control

E12:F5

Flame signal missing during the working

1. Check the flame sensor

2. verify the correct power connection

(see chapter 4.2.5.)

E12:F6

Overheating combustion control board

Check that the cooling fans in the components

compartment are working properly. Check and

cleaning air vents under the dashboard and

below the components compartment.

Summary of Contents for ANGELO PO COMBISTAR FX



















































































































































































Search results

Summary of Contents for ANGELO PO COMBISTAR FX

Reviews:

Related manuals for ANGELO PO COMBISTAR FX

Brands by name

Popular brands

MARMON ANGELO PO COMBISTAR FX, Technical Manual

Search results

Summary of Contents for ANGELO PO COMBISTAR FX

Reviews:

Related manuals for ANGELO PO COMBISTAR FX

Brands by name

Popular brands