Manusa VECTOR, Installation Manual

Page: 38 / 48

37
D00619EN - v0 SWING OPERATOR - INSTALLATION MANUAL
2. For double leaf with a central stop, it is necessary to configure a delay in the movement of the leaves.
During opening, normally a lesser delay is sufficient, mainly for ‘aesthetic’ reasons (as a maximum, one leaf
‘pushes’ the other a little during the first seconds of opening). When closing, where It is fundamental that one leaf
closes before the other to prevent rubbing, the delay is longer.
If the two leaves are SYNCHRONISED:
• configure only parameter 21 = 0 and parameter 22 = 0 on the MASTER card;
If the two leaves are NOT SYNCHRONISED:
• configure parameter 21 and parameter 22 only on the MASTER card to a value greater than 0.
3. To activate the operators, repeat the steps indicated in the section ‘Commissioning’, ensuring that the acquisition of
the parameters (points 6 and 7) is performed only from the card configured as MASTER.
WARNING: When starting the parameter acquisition task, the Master door begins first. Therefore, it is necessary to
stop the leaf during the next opening it performs. Immediately, the Slave door will start to move; for this, it is also
necessary to stop the leaf at the maximum opening required. Immediately afterwards, both doors will close completely
and the display will flash CL. When both leaves are closed, CL will remain on and the door will be ready for operation.
The program switch (optional) is connected solely and exclusively to the Master card using the same terminal plate used to
connect the two operators together. If the parameters are modified using the program switch, these are identical for both
cards. (Fig. 35) The closing operation begins from the output of both leaves completely open. Each time that a leaf reaches
the completely open position before the other, it will wait until the second one has also reached the completely
- open position.
The inverse (START 1 or 2, SAFE CLOSE, anti - crushing) occurs at the same time for both leaves.
Control of the electronic lock with its corresponding operational logic settings is allowed on both cards, exactly as for
individual operators.
The Push&Go function can be activated in both operators, in exactly the same way as for individual operators. When any
attempt to open a leaf is detected by either operator, it will cause both leaves to open.
The anti - crushing and obstacle detection is controlled by both cards, separately and independently.
If anti crushing protection is activated on one card during the closing phase, it will interrupt the movement of both leaves and
they will slowly open completely.
If anti - crushing protection is activated on one card during opening, it will interrupt the movement of the leaf in question and
will slowly close it completely. The other leaf meanwhile, having reached the completely open position, will wait for the leaf in
question before closing.
WARNING: The parameters that can be modified with MilleniumWare are independently on the two cards.
If modifications are made to the movement parameters, it is necessary to ensure the values configured are the same
on both cards to avoid malfunction.
Fig. 35.
6.2
B
L
O
C
K
G
N
D
D
A
T
A
PW
F
R
S
T
O
U
T
15
VD
C
C
O
M
A
U
X
-
I
N
2
A
U
X
-
I
N
1
S
T
A
R
T
2
S
T
A
R
T
1
C
O
M
K
EY
SA
F
E
-
C
L
O
SE
SA
F
E
-
O
P
EN
C
O
M
A
U
X
–
O
U
T
2
A
U
X
–
O
U
T
1
A
B A B +
-
-
+
MASTER
SLAVE
L
O
C
K
G
N
D
D
A
T
A
PW
F
R
S
T
O
U
T
15
VD
C
C
O
M
A
U
X
-
I
N
2
A
U
X
-
I
N
1
S
T
A
R
T
2
S
T
A
R
T
1
C
O
M
K
EY
SA
F
E
-
C
L
O
SE
SA
F
E
-
O
P
EN
C
O
M
A
U
X
–
O
U
T
2
A
U
X
–
O
U
T
1
A
B
A
B
+
- - +