Mantis FastStart Owner'S Manual Download Page 12

12

If you follow the normal

starting procedure, you should
have no problem starting your
tiller. But, just in case you do
have problems, here’s what to do.

Make sure the start/stop

switch is on “start.” You’d be
surprised how many people
forget to push the switch into the
“start” position.

If the switch was on “stop”

when you pulled the cord, you
may have flooded the engine.

•First, examine the spark plug.

Use the special wrench that
comes with our 

optional

MANTIS Handy Item Kit (Item
#1422) or a 3/4 inch spark plug
wrench. (Picture 1)

•Remove the cap over the spark

plug.

•Unscrew the spark plug.

(Picture 2)

Starting a Flooded
Engine

1. If the end of the spark plug

is wet, the engine may be
flooded. 

Make sure the switch 

is in the stop position,
disconnect spark plug wire and
remove plug. Use a paper towel
or a clean rag to dry the spark
plug, then, with the spark plug
out of the engine, pull the
starter cord several times.

Next, replace the spark plug. Use
the wrench to tighten it and
replace the cap. Next, put the
switch in the start position and
pull the choke button out. Pull
the starter cord three or four
times until the engine coughs or
sputters. Open the choke (push
the choke button in) and pull
the cord a few times. The engine
should start and run.

2. If the end of the spark plug

is dry, check to see if the fuel
line is blocked. First loosen the
fuel cap to relieve pressure in the
tank.  The fuel line runs from
the fuel tank to the carburetor.
Pull it off at the carburetor end.
Fuel should drip slowly from the
line. Wipe off any excess or
spilled fuel.

If fuel does not drip from the

line, check the line for any bends
or pinches. (Picture 3). Kinks in
the line restrict the flow of fuel
to the engine. Just straighten out
the line. Reconnect. Then follow
the normal starting procedure.

If fuel drips too freely, the line

may be disconnected from the
fuel filter. You’ll find the fuel
filter inside the fuel tank. Just re-
attach the line to the filter, and
put the filter back in the tank.
Then follow the normal starting
procedure.

Here’s Another Way to
Start your MANTIS

Tiller

If you follow the steps above

and your engine still won’t start,
try this:

1. Push the switch to “start.”

WARNING

MAKE SURE THE START/STOP

SWITCH IS IN THE 

STOP POSITION.

KEEP PLUG WIRE AWAY 

FROM ENGINE TO AVOID

UNINTENTIONAL SPARK.

IMPORTANT NOTE:
To avoid possible damage

to the threads, do not try
to remove the plug from a
hot aluminum cylinder
head.

WHAT TO DO JUST IN CASE

!

!

Picture 1

Picture 2

Picture 3

Summary of Contents for FastStart

































Reviews: