GB CREVICE CLEANER (P/N 8222)
38 tough steel bristle brushes mounted solidly on a sturdy steel wheel gives our Crevice Cleaner the power to
cut through weeds, dirt and debris in all those hard to reach places.
FR NETTOYEUSE DE CREVASSES
Les 38 brosses dures en fil d'acier, solidement montées sur une roue d'acier résistant, donnent suffisamment de
puissance à la nettoyeuse de crevasses pour pouvoir couper à travers les mauvaises herbes, la terre et les débris
dans tous les endroits difficiles à atteindre.
ES
CEPILLADORA DE GRIETAS
Treinta y ocho cepillos con cerdas de acero reforzado, instaladas firmemente en una rueda robusta de acero le
suministran la potencia necesaria a su cepilladora de grietas para cortar las yerbas, la tierra y los desechos en
esos lugares muy difíciles de limpiar.
Warnings - dos
Read and understand the owner’s manual. Pay particular attention to all
sections regarding safety.
1. Always keep a firm grip on both handles while the attachment is moving
and/or the engine is running. BE AWARE!! The tines may coast after throttle
trigger is released. make sure tines have come to a complete stop and engine is
off before letting go of the tiller.
2. Always maintain a firm footing and good balance, do not overreach while
operating the tiller. Before you start to use the tiller check the work area for obstacles
that might cause you to lose your footing, balance or control of the machine.
3. Always keep area clear of children, pets and bystanders.
4. Always stay alert. Watch what you are doing and use common sense.
Do not operate unit when fatigued.
5. Always dress properly. Do not wear loose clothing or jewellery, they might
get caught in moving parts. Use sturdy gloves. Gloves reduce the transmission
of vibration to your hands. Prolonged exposure to vibration can cause numbness
and other ailments. Wear non-skid foot wear to ensure secure and proper footing.
6. Always wear ear and eye protection. Eye protection must meet applicable CE
standards. To avoid hearing damage we recommend hearing protection be worn
whenever using the equipment.
7. Always keep a safe distance between two or more people when working together.
8. Always inspect your attachment before each use and ensure that all handles,
guards and fasteners are secure, operating and in place.
9. Always maintain and examine your tiller and attachments with care.
Follow maintenance instructions given in tiller manual.
10. Always store attachments in a sheltered area (a dry place) not accessible
to children. The tiller as well as fuel should not be stored in a house.
Warnings - don’ts
Don’t use tiller with one hand, keep both hands on handles with fingers and
thumbs encircling the handles, while attachment is moving, and engine is running.
Don’t overreach. Keep a good footing at all times.
Don’t attempt to clear attachment while it is moving. Never try to remove
jammed material before switching the engine off and making sure the attachment
has stopped completely.
Don’t allow children or incapable people to operate the tiller.
Don’t operate while under the influence of alcohol or drugs.
Don’t attempt to repair the attachment. Have repairs made by a qualified
dealer or repairman. See that only original Mantis parts are used.
GB
WARNING • DANGER
IMPROPER USE OR CARE OF THESE ATTACHMENTS OR FAILURE TO WEAR PROPER PROTECTION
CAN RESULT IN SERIOUS INJURY.
READ AND UNDERSTAND THE RULES FOR SAFE OPERATION AND ALL INSTRUCTIONS IN THIS MANUAL.
WEAR HEARING AND EYE PROTECTION.
Engine fuel warnings - do’s
Always use fresh petrol in the fuel mixture. Stale petrol can cause leakage.
Always pull starter cord slowly until resistance is felt. Then pull cord rapidly
to avoid kickback and prevent arm or hand injury.
Always operate engine with spark arrestor installed and operating properly.
Engine/fuel warnings - don’ts
Don’t fuel, refuel or check fuel while smoking or near an open flame or
other ignition source. Stop engine and be sure it is cool before refueling.
Don’t leave the engine running while the tiller is unattended. Stop engine
before putting the tiller down or while transporting from one place to another.
Don’t refuel, start or run this tiller indoors or in an improperly ventilated area.
Don’t run engine when electrical system causes spark outside the cylinder.
During periodical checks of the spark plug, keep plug a safe distance from
cylinder to avid burning of evaporated fuel from cylinder.
Don’t check for spark with spark plug or plug wire removed. use
an approved tester.
Don’t crank engine with spark plug removed, except when preparing
to store tiller for the off season.
Don’t run engine when the odor of petrol is present or other explosive
conditions exist.
Don’t operate the unit if petrol is spilled. Clean up spill completely
before starting engine.
Don’t operate your tiller if there is an accumulation of debris around the
exhaust and cooling fins.
Don’t touch hot exhaust, cylinders or cooling fins as contact may cause
serious burns.
WARNING • DANGER
HANDLE FUEL WITH CARE, IT IS HIGHLY FLAMMABLE. FUELING A HOT ENGINE OR NEAR AN IGNITION
SOURCE CAN CAUSE A FIRE AND RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
CREVICE CLEANER
All attachments mount on the tine shafts and are held in place with retaining pins. Attachment maintenance is very simple.
Just clean with your garden hose. When dry, spray with a light pressurized oil like WD40.
Note: In the instructions that follow, assume that you are standing behind the Tiller as you would in tilling or cultivating.
418-1
9222-21
4106
486
416A
WARNING
AFTER MOUNTING BRUSH TO A MACHINE, START MACHINE AND RUN AT OPERATING SPEED IN A PROTECTED ENCLOSURE FOR AT LEAST ONE MINUTE BEFORE USING, DURING
WHICH NO ONE SHALL STAND IN FRONT OF, OR IN LINE WITH, THE BRUSH. SAFETY GOGGLES OR FULL FACE SHIELDS WORN OVER SAFETY GLASSES WITH SIDE SHIELDS MUST BE
WORN BY ALL OPERATORS AND OTHERS IN THE AREA OF POWER BRUSH OPERATIONS. COMPLY WITH THE REQUIREMENTS OF ANSI Z87.1. END BRUSH SHANKS MUST BE FULLY
INSERTED INTO THE CHUCK OR COLLECT AND TIGHTENED SECURELY. REFER TO AND COMPLY WITH ANSI B 165.1 FOR FURTHER SAFETY INSTRUCTIONS.
How to Mount
First remove the existing tine attachment on your tiller.
Place the Crevice Cleaner on one side of the unit and the
idler wheel on the other. Be certain that the retaining pins
are inserted on both the left and right axles before using the
Crevice Cleaner. Slip on the hood extender over the Crevice
Cleaner brush by bending it in a semi-circle so the channels
on the extender slip over the front and back edges of the tiller
hood. Push it in towards the transmission.
How to Use
IMPORTANT; WEAR YOUR GOGGLES!
For hard surfaces such as concrete, pull the tiller towards you
with the Crevice Cleaner going into the area that you want to
clean. For softer material such as blacktop, brick or slate, work
the tiller backwards and forwards in a sweeping motion so
that the Crevice Cleaner is perpendicular to the crevice.
NOTE: Be sure to first test the proper cleaning method
and rotation speed in an inconspicuous area for the type
of material you are trying to clean.
OPERATING INSTRUCTIONS AND PARTS LISTS
!
!
400721 CreviceCleaner GBFRES Cond_PF 4084 11/28/11 4:22 PM Page 1
