background image

 

 
 
 
 
 
 
 
 

 

AVS C-Series – AVS C3/C4/C5 

Installation  manual 

 

Generation 1 Version 1261 

Serials: (21)1141580 – Current 

Build date: 01/09/2015 > 

Make sure you are using the correct manual 

 

 

AVS C-Series range

 features: 

 

Control the alarm via factory remotes (or additional AVS CANREMOTES) 

 

Red LED warning light 

 

PIN code override via LED button 

 

Simple programming of features from PC software 

 

Arm the alarm with ultrasonic and additional sensors disabled 

 

Auto zone bypass 

 

Door ajar warning 

 

Past alarm trigger memory (PAT) 

 

Factory door, boot and bonnet sensor protection (additional bonnet PIN included for some vehicles) 

 

AVS C3

 additional features: 

 

Dual tone standard siren 

 

AVS C4

 additional features: 

 

Dual tone battery back-up siren 

 

Plug-in ultrasonic sensors 

 

AVS C5

 additional features: 

 

Dual tone battery back-up siren 

 

Plug-in ultrasonic sensors 

 

Plug-in digital tilt sensor 

 

 
Programmable features: 

 

Optional AVS CANREMOTE control* 

 

Control by CAN – Hazard lights, window rollup, central locking* 

 

OEM alarm detection* 

 

Arm and disarm chirp 

 

Door lock on ignition 

 

Automatic re-arm and re-lock 

 

*vehicle dependent, may require additional parts 

 
 
 
 
 
 
 

Manta help line 09 476 8052 

 

AVS is a registered trademark of the 

group of companies 

Summary of Contents for AVS C Series























Reviews: