manualshive.com logo in svg

Manitowoc RF0300, Technician'S Handbook

Share
Download
Manitowoc RF0300 Technician'S Handbook Download Page 108

108 

Part Number 000007661 11/16 

RF2300C/RFS2300C Troubleshooting

QUIETQUBE REMOTE AIR-COOLED MODELS WITH 

REMOTE CONDENSING UNIT
Normal Operation

When the toggle switch is placed in the ON position the 
following controls must be in the closed position before 
the ice machine will start:

A.  Bin Thermostat
B.  High Pressure Cut-out Switch
C.  Ice Chute Safety Switch
D.  Low Pressure Switch
E.  Low Water Level Switch

Placing the toggle switch in the ON position starts the 
gear motor. After the rotation speed sensor verifies 10 
minutes of correct rotation the time delay ends and the 
liquid line solenoid valve opens. 
•  When the refrigerant pressure is high enough to close 

the low-pressure control the contactor coil energizes 
and the compressor starts.

•  The refrigerant pressure will increase and close the 

fan cycling pressure control and the condenser fan 
motor starts.

The ice machine will continue to make ice until ice 
contacts the bin thermostat and the liquid line solenoid 
valve closes and the refrigeration system pumps down.
•  The refrigerant pressure drops and the fan cycling 

pressure control opens stopping the condenser fan 
motor.

•  When the refrigerant pressure is low enough to open 

the low pressure control, the contactor coil is de-
energized and the compressor stops.

NOTE: The ice machine remains off until ice no longer 
contacts the bin thermostat.

Summary of Contents for RF0300





























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands