background image

Section 7

Refrigeration System

 Part Number 80-1634-3

7-29

REFRIGERANT DEFINITIONS

Recover

To remove refrigerant, in any condition, from a system 
and store it in an external container, without necessarily 
testing or processing it in any way.

Recycle

To clean refrigerant for re-use by oil separation and 
single or multiple passes through devices, such as 
replaceable core filter-driers, which reduce moisture, 
acidity and particulate matter. This term usually applies 
to procedures implemented at the field job site or at a 
local service shop.

Reclaim

To reprocess refrigerant to new product specifications 
(see below) by means which may include distillation. A 
chemical analysis of the refrigerant is required after 
processing to be sure that product specifications are 
met. This term usually implies the use of processes and 
procedures available only at a reprocessing or 
manufacturing facility.

Chemical analysis is the key requirement in this 
definition. Regardless of the purity levels reached by a 
reprocessing method, refrigerant is not considered 
“reclaimed” unless it has been chemically analyzed and 
meets ARI Standard 700 (latest edition).

New Product Specifications

This means ARI Standard 700 (latest edition). Chemical 
analysis is required to assure that this standard is met.

Summary of Contents for MARINE MODEL S1800





































































































Reviews: