Malaguti Dune X 125 Page 66 Service Station Manual Download

Page: 66 / 272

Dune 125 - Dune X 125 - Euro 4

Electrical system

ELE SYS - 66

MAIN WIRING HARNESS



Place the main wiring harness (1) in- side

the chassis making sure that the red

taping is placed near the metal flanges

which must be covered with a piece of

PVC pipe.

MAIN WIRING HARNESS



Place the main wiring harness (1) on

the metal flange which must be cov-

ered with a piece of PVC pipe.

MAIN WIRING HARNESS



Place the main wiring harness (1) on

the metal flanges and tighten them to

stop the wiring harness from moving.

Summary of Contents for Dune X 125

















































































































































































































































































Search results

Summary of Contents for Dune X 125

Reviews:

Related manuals for Dune X 125

Brands by name

Popular brands

Malaguti Dune X 125, Service Station Manual

Search results

Summary of Contents for Dune X 125

Reviews:

Related manuals for Dune X 125

Brands by name

Popular brands