Malaguti Dune X 125 Page 139 Service Station Manual Download

Page: 139 / 272

Dune 125 - Dune X 125 - Euro 4

Engine

ENG - 139

RANKSHAFT

Pos.

Description

Type

Quantity

Torque

Notes

Gear fixing screw

M10

40 Nm (29.50 lb ft)

Balancing countershaft removal



Before taking out the balancing coun-

tershaft the clutch cover and flywheel

cover must be removed.



Lock the countershaft with the specific

tool.

Specific tooling

864486 Countershaft lock tool



Unscrew and remove the nut and col-

lect the washer



Remove the countershaft gear.



Remove the countershaft from the al-

ternator side.

Summary of Contents for Dune X 125

















































































































































































































































































Search results

Summary of Contents for Dune X 125

Reviews:

Related manuals for Dune X 125

Brands by name

Popular brands

Malaguti Dune X 125, Service Station Manual

Search results

Summary of Contents for Dune X 125

Reviews:

Related manuals for Dune X 125

Brands by name

Popular brands