13 ENGLISH
Reverse button for debris removal
WARNING:
If the entangled branches or
debris cannot be removed by the reverse func-
tion, switch off the tool and remove the bat
-
tery cartridge, and then remove the entangled
branches or debris using tools such as pliers.
Failure to switch off the tool and remove the bat
-
tery cartridge may result in serious personal injury
from accidental start-up. Removing the entangled
branches or debris by hand may cause an injury,
since the shear blades may move in reaction to
removing them.
This tool has a reverse button to change the direction
of shear blades movement. It is only for removing
branches and debris entangled in the tool.
To reverse the shear blades movement, press the
reverse button when the shear blades have stopped,
then pull the front switch trigger, and then pull the rear
switch trigger while pressing the lever. The power lamp
starts blinking, and the shear blades move in reverse
direction.
When entangled branches and debris are removed,
the tool returns to the regular movement and the power
lamp stops blinking and lights up.
►
Fig.6:
1.
Power lamp
2.
Reverse button
NOTE:
If the entangled branches or debris cannot be
removed, release the switch triggers, then press the
reverse button, and then pull the switch triggers until
they are removed.
NOTE:
If you tap the reverse button while the shear
blades are still moving, the tool comes to stop and to
be ready for reverse movement.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
CAUTION:
When replacing the shear blades,
always wear gloves so that your hands do not
directly contact the blades.
NOTICE:
When replacing the shear blades, do
not wipe off grease from the gear and crank.
Installing or removing the shear
blades
CAUTION:
Attach the blade cover before
removing or installing the shear blades.
You can install 600 mm or 750 mm shear blades to your
tool.
NOTE:
If you change the shear blades to a different
length, replace the chip receiver with one which fits
the blades.
1.
Remove 4 screws (for DUH604S) or 5 screws (for
DUH754S), and then remove the chip receiver from the
tool.
►
Fig.7:
1.
Chip receiver
2.
Screw
2.
Place the tool upside down, and then remove 6
bolts.
►
Fig.8:
1.
Bolt
3.
Remove the cover and the plate.
►
Fig.9:
1.
Cover
2.
Plate
NOTE:
The plate may remain on the cover.
4.
Remove the rod and the bearing.
►
Fig.10:
1.
Rod
2.
Bearing
NOTE:
The rod or bearing may remain on the cover.
5.
Remove 3 screws, 3 washers, 3 sleeves and the
felt pad, and then remove the shear blades.
►
Fig.11:
1.
Screw
2.
Washer
3.
Sleeve
4.
Felt pad
5.
Shear blades
NOTICE:
Be careful not to lose the screws and
washers.
6.
Remove the blade cover, and then attach it to the
new shear blades.
►
Fig.12
7.
Adjust the crank so that 2 holes are lined up on
the alignment line.
►
Fig.13:
1.
Hole
2.
Alignment line
8.
Align the protrusions on the shear blades vertically
at the same position.
►
Fig.14:
1.
Protrusion
9.
Insert the screw and the washer removed in step
5 into the hole on the shear blades to temporarily fix the
shear blades, and then attach the felt pad to the shear
blades.
►
Fig.15:
1.
Screw
2.
Washer
3.
Felt pad
4.
Hole
10.
Insert the protrusion on the shear blades to the
hole on the rod, then align the position of the felt pad
with the holes on the tool. Attach 2 new sleeves and 2
washers.
►
Fig.16:
1.
Felt pad
2.
Protrusion
3.
Hole
4.
Washer
5.
Sleeve
NOTICE:
Apply a small amount of grease to the
inner periphery of the hole of the rod.
NOTICE:
Be careful not to lose the washers and
the sleeves.
11.
Align the holes on the washers, sleeves, and
shear blades with the holes on the tool, and then tighten
2 screws to temporarily fix the shear blades.
►
Fig.17:
1.
Screw
12.
Attach a new sleeve.
►
Fig.18:
1.
Sleeve
13.
Remove the screw and the washer inserted into
the hole on the shear blades in step 9, and then tighten
the screw together with the sleeve and the washer to fix
the shear blades.
►
Fig.19:
1.
Screw and washer
Summary of Contents for DUH604S
