background image

BOXER SERIES 10-20 KVA 

 

EXPLANATIONS OF LOGGING

 

AG-SD-109 Publishing Date: 13.10.2015 Revision No: 0 Rev. Date:

 

 

41 

BYPASS Thyristor 

L2 Short Circuit 

UPS  has  detected  short  circuit  at  bypass  L2  thyristor.  UPS  will 
shut down. 

42 

BYPASSThyristorL3 

Short Circuit 

UPS  has  detected  short  circuit  at  bypass  L3  thyristor.  UPS  will 
shut down. 

43 

UPS ThyristorL1 

Short Circuit 

UPS  has  detected  short  circuit  at  inverter  L1  thyristor.  UPS  will 
shut down. 

44 

UPS  Thyristor  L2 
Short Circuit

 

UPS  has  detected  short  circuit  at  inverter  L2  thyristor.  UPS  will 
shut down. 

45 

UPS  Thyristor  L3 
Short Circuit

 

UPS  has  detected  short  circuit  at  inverter  L3  thyristor.  UPS  will 
shut down. 

46 

UPS ThyristorL1 

Open Circuit 

UPS has detected that inverter L1 thyristor cannot be activated. 

Load will be transferred to bypass line. 

47 

UPS  Thyristor  L2 
Open Circuit

 

UPS has detected that inverter L2 thyristor cannot be activated. 

Load will be transferred to bypass line. 

48 

UPS  Thyristor  L3 
Open Circuit

 

UPS has detected that inverter L3 thyristor cannot be activated. 

Load will be transferred to bypass line. 

49 

BYPASS 

ThyristorL1 Open 

Circuit 

UPS  has  detected  that  bypass  L1  thyristor  cannot  be  activated. 
Load will be transferred to inverter line. 

50 

BYPASS 

ThyristorL2Open 

Circuit 

UPS  has  detected  that  bypass  L2  thyristor  cannot  be  activated. 
Load will be transferred to inverter line. 

51 

BYPASS 

ThyristorL3 Open 

Circuit 

UPS  has  detected  that  bypass  L3  thyristor  cannot  be  activated. 
Load will be transferred to inverter line. 

52 

Parallel  System 
Phase Sequence 

Error 

One or more of UPSs which operate in parallel mode do not match 
in phase sequence. 

53 

Battery Start 

UPS was given the command to start from the battery. 

54 

Parallel Start Error 

One or more of UPSs which operate in parallel mode could not be 
prepared to operate. 

55 

Inverter Error 

UPS couldn't prepare the inverter voltage when it was started. 

56 

Output Off 

Static transfer switches all disabled. The loads cannot be 
energized. 

57 

Normal Mode 

UPS is operating in the normal mode, loads are energized through 
rectifier – inverter line. 

58 

Battery Mode 

UPS is operating in the battery mode, loads are energized through 
battery – inverter line. 

59 

Bypass Mode 

UPS is operating in the bypass mode, loads are energized through 
bypass line. 

60 

Maintenance Bypass 

Mode 

UPS is operating in the maintenance bypass mode, loads are 
energized through maintenance bypass line. 
 

61 

Parallel Mode 

2 or more UPS are operating in power sharing mode. Load is fed 

through UPSs’ inverter lines. 

 

Summary of Contents for BOXER BX3310





























































Reviews: