background image

 

 

Version: 1.05, 05.10.18 

  

15 

10

 

EU Declaration of Conformity 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EU  Declaration of Conform ity  

in accordance with the Low  Voltage Directive (LVD) 2014/35/EU  

 

Manufactorer: 

Lightpower G m bH  

 

An der Talle 24 -28  

 

D-33102 Paderborn 

 
Authorized person for the issuance  
of the declaration  of conform ity : 

Andr

é

 Raude 

 

U lm enweg 2  

 

32832 Augustdorf 

 
 

Product 
m odel 

Product descriptio n  

4001408 

DMX -Merger 2 in1 , X LR5 

4001733 

DMX -Merger 3in1 , X LR5 

4002164 

DMX -Merger 3in1 , RJ45 

 
 
We hereby certify that the above-nam ed pro duct(s),

 

as we p ut the execution 

into circulatio n, is/are conform  with  the regulations of the fo llow ing EU -
directives:   
 
Low Voltage Directive (LVD) 2014/35/EU   
(EMC) Directive 2014/30/EU   
RoHS Directive (2011/65/EU ) 
 
Applied harm onized standards: 
 
EN 60204 -1 
91/263/EWG ; 92/31/EWG ; 93/68/EWG  
 
The ob ject of the declaration described abov e is in  conform ity with the relevant 
U nio n harm o nisatio n leg islation. Any m od ification of this prod uct(s) with out 
confirm ation shall auto m atically ann ul this d eclaration. 
 

 

 

 

 

 

 

 

 

 

 

 

          

 

Paderborn, 28th Aug ust, 2018   

 

Andr

é

 Raude 

Summary of Contents for 4001733

















Reviews: