background image

 

 

12

 

  

Version: 1.05, 05.10.18 

7

 

Submenu 3,4,5 

 DMX insert address for input A, B, 

Via these 3 sub-menus, an insert address (OFF-SET) can be assigned to 
each of the three inputs, from which the respective channel values are 
then merged into the output values according to the set MERGE MODE.  

 

INPUT A 

  

@ DMX: 001 

Menu 3, 

or 

INPUT B 

  

@ DMX: 301 

Menu 4, 

or

 

INPUT C 

  

@ DMX: 451 

Menu 5 

 

With the "UP/DOWN" - keys the currently displayed address value can 
now be changed either up or down. In this case, the value changes 
slowly at first, and much faster in the corresponding direction after one 
second. Click on the "OK" - key to save the settings. 

Here is a possible application using the given example addresses: 

large

“ 

lighting console controls at input A the entire DMX area of one 

event location. A second, smaller lighting console has access to the 
lighting circuits of the foyer at input B from DMX 301, but via its own DMX 
channels from address 1. 

A mobile dimmer controls temporaly added lights for object lighting from 
address 451, which can be set with a simple 12 channel DMX console 
without influencing the permanently installed circuits. 

Please notice:

  

If the OFFSET address is changed for an input, the management table 
for the "last value changes" is reset internally. All channels below the new 
address are assigned the value 0 ("source unknown"), from and above 
the address the assignment to the currently reconfigured input. If the 
merger is working in LTP mode, this input temporarily takes over control 
in its address range, all other values initially fall back to control through 
input A. 

 

Summary of Contents for 4001733

















Reviews: