Majestic fireplaces NVCR36R Series Installation And Homeowner’S Operating Manual Download Page 1

INSTALLER/CONSUMER 
SAFETY INFORMATION

PLEASE READ THIS MANUAL 
BEFORE INSTALLING AND USING 
APPLIANCE.
IMPORTANT:

 Read all instructions 

and warnings carefully before starting 
installation. Failure to follow these 
instructions may result in a possible 
fire hazard and will void the warranty.

WARNING: If the information in this 
manual is not followed exactly, a fire 
or explosion may result causing 
property damage, personal injury or 
loss of life.
FOR YOUR SAFETY
Installation and service must be per-
formed by a qualified installer, service 
agency or the gas supplier. Do not 
store or use gasoline or other 
flammable vapors and liquids in the 
vicinity of this or any other appliance.
FOR YOUR SAFETY
If you smell gas:
1.  Open windows. 
2.  Do not touch any appliance.
3.  Extinguish any open flame.
4.  Do not use the phone in your 
  building.
5.  Immediately call your gas supplier 

from a neighbor’s phone.

6.  Follow your gas supplier’s 
  instructions.
7.  If you cannot reach your gas 
  supplier, call the fire department.

Decorative Gas Appliances

Models: NVCR36R, NVCR36L

Installation and Homeowner’s 

Operating Manual

1315

NVCR

Cover

4/30/99   djt

CERTIFIED

DESIGN

CERTIFIED

20001315  10/06  Rev. 5

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

f i r e - p a r t s . c o m

Summary of Contents for NVCR36R Series

























Reviews: