manualshive.com logo in svg

Majacraft M WH ROSE, Instruction Manual

The Majacraft M WH ROSE is a top-of-the-line spinning wheel, designed for experienced fiber artists. To help you fully utilize its features, we provide a comprehensive Instruction Manual that you can easily download for free from our website. Get the most out of your spinning experience with our detailed manual at manualshive.com.

Share
Download
background image

9

majacraft

Starting with the right pedal (it will be on your left if you are facing the drive wheel), remove the 

gold 25mm screw from the side of the pedal. Choose the conrod with the #1 stamped on the bottom 

and push the green joiner through the hole in the pedal. It should protrude through the bottom of 

the pedal about 1mm-2mm. Check the alignment of the outer rod end in the crank assembly. When 

the rod end is aligned correctly, screw the 25mm screw back into place. The screw should only be 

tightened until the head just touches the  side of the pedal. DO NOT OVERTIGHTEN!

Now the left pedal (it will be on your right if you are facing the drive wheel), remove the gold 25mm 

screw from the side of the pedal. Choose the remaining conrod and push the green joiner through 

the hole in the pedal. It should protrude through the bottom of the pedal about 1mm-2mm. Check 

the alignment of the rod end in the crank assembly as shown below. When the rod end is aligned 

correctly, screw the 25mm screw back into place. The screw should only be tightened until the head 

just touches the  side of the pedal. DO NOT OVERTIGHTEN!

Align the holes on the drive wheel with the holes in the crank 

assembly and screw it into place using the silver 32mm screws. It is 

recommended that you insert the centre screw first.

Required:

2 - Gold 25mm (1”) screws 

(in the pedals)

Posidrive screwdriver

10.  Conrods to Pedals

Fit the green joiners in the wooden footmen to the pedals. We leave a mark on one conrod (a #1 on 

the bottom end) and the right pedal (#1 by the screw hole) to ensure that each conrod is attached to 

the correct pedal.

CORRECT

INCORRECT

9b

9c

10a

10b

Summary of Contents for M WH ROSE













Reviews:

No comments

Related manuals for M WH ROSE

Brands by name

Popular brands

Load more brands