Maipu S12800 Installation Manual Download Page 113

Page: 113 / 135

S12800 Routing Switch Installa

tion Manual V1.0

Maipu Confidential & Proprietary Information

Page 113

B.2

USB Console Port Attribute

S12800 provides one USB Console port complying with USB2.0 specifications. With the
interface, the user can complete the local configuration for the switch. For the attributes of
Console port, refer to the appendix table A-2:

Appendix table B-2 The attributes of the USB Console port

Attribute

Description

Interface standard

USB2.0

Connector type

Micro USB

Rate

12Mbps

Supported services

Connected with the USB of local terminal (PC) and run the

terminal emulation program on the terminal (the range of the
baud rate is 9600bit/s-115200bit/s (the default value is

9600bit/s))



To use the USB console port, you need to install the drive software on the local terminal
(PC).

B.3

10Base-T/100Base-TX/1000Base-T RJ45 Electrical Port Attributes

Appendix table B-3 10Base-T/100Base-TX/1000Base-T RJ45 Electrical Port Attributes

Attribute

Description

Interface standard

IEEE 802.3, IEEE802.3u, IEEE802.3ab

Connector type

RJ45

Work mode

10Mbps/100Mbps/1000Mbps

Half-duplex/full-duplex/auto-negotiation

Maximum transmission distance

100m

Specifications of used cable

Category-5 or above twisted pair

Summary of Contents for S12800








































































































































Search results

Summary of Contents for S12800

Reviews:

Related manuals for S12800

Brands by name

Popular brands

Maipu S12800, Installation Manual

Search results

Summary of Contents for S12800

Reviews:

Related manuals for S12800

Brands by name

Popular brands