Maico ESQ 25/4 Mounting And Operating Instructions Download Page 13

 

 

13 

 Screw the unit securely to the ceiling, wall, 

floor or bracket with the exhaust air outlet 
directed upwards. Make sure you have  
available amply dimensioned mounting 
material. 

 Install suitable folded spiral-seams duct. 

Make sure that the ducting is not 
twisted when you fit it. 

 

 Electrical connection 

8.2

 

DANGER 

Danger to life from electric 
shock. 

 Switch the mains fuse off. 

 Position a warning notice to 

avoid the unit being 
accidentally switched back on. 

 

CAUTION 

Danger of short-circuits 
through incorrect feeding of 
the power cable into the 
terminal box. 

 Feed the power cable 

correctly through the cable 
screw-connection. 

 

Notes 

 Always note the relevant specifications  

for electrical installations and when fitting 
equipment. In Germany observe DIN  
VDE 0100 and the corresponding parts  
in particular. 

 The cabling between the power and the 

terminal box must be permanent. 

 Units are speed controllable with  

 frequency converters (only DSQ..  

   and DSQ.. K) or  

 transformers. Select the best option 

depending on the current input. Speed 
control through the use of phase angles  
is 

not

 permitted! 

 
 
 
 
 
 

Connect the unit electrically 

 In the case of standard units, remove the 

side panel [3] and feed the power cable 
through the cable screw-connection [6] in 
the housing. Ensure that the cable screw-
connection seals off the power cable 
tightly. The cable screw-connection also 
serves as a tension relief. 

 Remove the terminal box cover. 

 
 
 
 
 
 
 
 
 

 

CAUTION 

Danger of short-circuits 
caused by damp if the power 
cable is not inserted correctly 
into the terminal box. 

 Insert the power cable into the 

terminal box such that the 
cable screw-connection fits 
tightly round the power cable. 

 Connect the power cable to the connection 

terminal [7.1] or [13.1] respectively, as 
shown on the inside of the terminal box 
cover. 

 Connect a suitable motor overload protect-

tion device. 

 Put the terminal block cover on and screw 

it into place. 

 In the case of standard units, fit side  

panel [3] and secure with the two  
catches [3.1]. 

GB

Summary of Contents for ESQ 25/4

















Reviews: