Maico Centro-E Installation And Operating Instructions Manual Download Page 9

13 Spare parts

9

Fault

Cause → Measure

Fan performance inad-
equate.

Dirty filter. → Replace
filter.

Locking hook not en-
gaged. → Engage fan
insert correctly.

Incorrect duct diameter.
→ Check diameter of
the main duct.

Supply air cross section
is too small. → Increase
the supply air cross
section.

Spiral housing too loud. Dirty filter. → Replace

filter.

Fan insert incorrectly in-
stalled. → Insert fan in-
sert correctly in accord-
ance with these instruc-
tions.

The main duct is under-
sized. → Re-calculate
pressure losses.

H model does not
switch from base load
to full load operation
despite there being hu-
midity in the room.

No rapid increase in hu-
midity (7% in 2 minutes)
took place.

H model no longer
switches back to base
load operation or off
even after a long period
in full load operation.

The level has not yet
fallen below reference
value. After 1 h, the
valve automatically
switches from full load
operation to base load
operation after an over-
run time of 15 minutes
and resets the refer-
ence value.

Additional consumers
connected to terminal 4.

Damage to the unit if
connected incorrectly.

Do not connect addi-
tional consumers to ter-
minal 4.

The unit may only be
connected according to
the wiring diagrams
(Wiring diagrams).

 If the fault persists or reoccurs

: Disconnect

the unit completely from the power supply. Let a
qualified electrician determine the cause of the
fault and eliminate it. If you have any question re-
lating to troubleshooting: Service: +49 7720 6940.

13 Spare parts

 Spare parts may only be sourced from and

fitted by a specialist installer.

Designation

Article no.

Spiral housing, cpl.

Centro-M

Centro-E

Centro-H

E084.0182.0000

E084.0183.0000

E084.0187.0000

Cover ABD ER 60/100/
Centro

E059.1017.9000

Filter mat ZF 60/100: 5
pieces, filter class G2
according to EN 779
with filter change indic-
ator (time strip)

0093.0331

In case of questions, please contact:

Maico Elektroapparate-Fabrik GmbH
Steinbeisstraße 20
78056 Villingen-Schwenningen, Deutschland
Tel. +49 7720 694 445
Fax +49 7720 694 175
E-mail: 

[email protected]

 Spare parts

 can be ordered at

www.shop.maico-ventilatoren.com

.

Summary of Contents for Centro-E













Reviews: