manualshive.com logo in svg

Mahlkonig E80 GbW, Operating Manual, Page: 40 / 47

Share
Download
Mahlkonig E80 GbW Operating Manual Download Page 40

Troubleshooting

Fault

Cause

Remedy

The grinder is 

not grinding, 

the display is 

not lit up.

• 

The power 

plug is not 

plugged into a 

socket.

 

t

Insert the power plug into a properly 

installed socket.

• 

The bean hop-

per has not 

been inserted.

 

t

Insert the bean hopper (see chapter on 

"Setting up the grinder and inserting 

the bean hopper").

• 

The overcur-

rent protec

-

tion switch has 

been trig-

gered.

 

t

Check whether the release button of 

the circuit breaker has popped out. 

Push it back in if necessary. Contact 

your service partner if the circuit break-

er pops out repeatedly (see chapter on 

“Maintenance and service”).

• 

The electri-

cal fuse has 

tripped.

 

t

Check the electrical fuse. If required, 

restore the fuse to its original state 

or replace it. Check whether other 

loads are connected to this fuse and if 

so, pull out their plugs. Contact your 

service partner if the fuse repeatedly 

trips (see chapter on “Maintenance and 

service”).

E80 GbW | F80 GbW | EN

ESPRESSO GRINDER| FILTER COFFEE GRINDER

40

Summary of Contents for E80 GbW
















































Reviews:

No comments