manualshive.com logo in svg

Mahlkonig E80 GbW, Operating Manual, Page: 19 / 47

Share
Download
Mahlkonig E80 GbW Operating Manual Download Page 19

If the bean hopper cannot be fixed in place by turning it, it may not be 

positioned correctly. In this case, align the bean hopper correctly 

 

(see step 5) and then try again by pressing it down and turning it 

 

(see also the chapter on “Troubleshooting”).

7. 

Use a slot screwdriver to tighten the securing screw 

(19)

 for the bean 

hopper clockwise.

The grinder switches off automatically if the bean hopper is not 

attached.

Setting up the portafilter support and spout

ONLY RELEVANT FOR E80 GBW.

You will need a slot screwdriver to adjust the portafilter support 

(not included with delivery).

Adjust the portafilter support 

(11)

 to the size of the portafilter of your coffee 

grinder (see 

Fig. C

):

1. 

Make sure the grinder is switched off (On/Off switch 

(5)

 in position 0).

2. 

Use a screwdriver to unscrew the screws

 (8)

 for adjusting the portafilter 

support (left and right) by turning them anticlockwise.
The portafilter support is lowered as far as it will go.

3. 

Insert the portafilter in the portafilter intake 

(12)

.

4. 

Push the portafilter support upwards until the portafilter fits exactly 

between the portafilter support and the portafilter intake.

If the portafilter support does not fit, contact your supplier 

 

(see chapter on “Maintenance and service”).

5. 

Hold the portafilter support in position and fix it by tightening the screws 

for adjusting the portafilter support (left and right) clockwise with a slot 

screwdriver.

6. 

Push the spout guide 

(20)

 up or down in the locking mechanism to align 

the spout 

(13)

 in the optimum position for your portafilter (see 

Fig. E

).  

Align the spout in such a way that the ground material falls from the 

spout into the centre of the inserted portafilter. 

19

E80 GbW | F80 GbW | EN

18

Summary of Contents for E80 GbW
















































Reviews:

No comments