59
BA053101-en
Pos: 205 /Technis che Dok umentation/A lle G eräte/ Überschr iften/Üb erschriften 1/V/ Überschrift 1: Vorbereitung zur Prüfung @ 6\mod_ 1182866197218_75.d ocx @ 97762 @ 1 @ 1
8
Preparations for Testing
Pos: 206 /Technis che Dok umentation/A lle G eräte/ Überschr iften/Üb erschriften 1.1/P/ Überschr ift 1.1: Prüfs tand einschalten @ 13\m od_1234338282712_ 75.docx @ 337911 @ 2 @ 1
8.1
Switch on the Dyno
Pos: 207 /Technis che Dok umentation/ Leis tungsmesstechnik/POWE RDYNO/052301 LPS 3000 R100/BA/Inhalt: 0523 Prüfstand eins chalten @ 13\mod_ 1234338731466_ 75.docx @ 337937 @ @ 1
1 Switch on the main switch at the communication desk.
2 Turn the Operating mode switch to position 2 "Setup".
3 Push the Control ON button.
See also section "Description / Controls and Indicators".
Pos: 208 /Technis che Dok umentation/A lle G eräte/ Überschr iften/Üb erschriften 1.1/P/ Überschr ift 1.1: Prüfs tand befahren und Fahrzeug fixieren @ 14\mod_1241610689527_ 75.docx @ 371981 @ 2 @ 1
8.2
Drive onto Dyno and Secure Vehicle
Pos: 209 /Technis che Dok umentation/ Leis tungsmesstechnik/POWE RDYNO/053101 M SR/ BA/Inhalt: 0531 Pr üfstand befahren und Fahrzeug fix ieren (Bilder) @ 14\mod_ 1241610760668_ 0.d ocx @ 372007 @ @ 1
Pos: 210 /Technis che Dok umentation/ Leis tungsmesstechnik/- Archiv -/ 00 LPS A lle/Inhalte/Warnung!/Inhalt: Warnung - Verletzungs gefahr d urch Partikel @ 13\mod_ 1234338898507_75.d ocx @ 337989 @ @ 1
Risk of injury by flying particles!
•
Before driving onto the rollers, remove all particles such as gravel etc. from the tires.
•
Check the balancing weights on the rims for tight fit.
•
Wear protective glasses.
Pos: 211 /Technis che Dok umentation/ Leis tungsmesstechnik/POWE RDYNO/053101 M SR/ BA/Inhalt: 0531 Pr üfstand befahren und Fahrzeug fix ieren (Text) @ 14\mod_ 1241610870809_ 75.docx @ 372033 @ @ 1
1 Block the rollers.
2 Position the front axle in the center on top of the front roller set.
3 Put on the parking brake.
4 Fix the vehicle at the front with tightening straps, and with chains at the rear. The anchoring
should be tight, but not pull down the vehicle.
5 Release the parking brake and shift to idle position.
6 Move the rear roller set until the rear axle also sits centered on the top.
7 Retighten the vehicle fixing again.
8 Release the roller blocking.
Pos: 212 /Technis che Dok umentation/ Leis tungsmesstechnik/- Archiv -/ 00 LPS A lle/Inhalte/Warnung!/Inhalt: Warnung - Lebens gefahr bei Losreißen des FZGs @ 17\mod_ 1253775470018_ 75.docx @ 447663 @ @ 1
