manualshive.com logo in svg

Magtrol 3411, User Manual, Page: 37 / 59

Share
Download
Magtrol 3411 User Manual Download Page 37

28

Magtrol Model 3411 Torque Display

Chapter 5 – Computer Controlled Operation

OPERA

TION

5.3.4 

U

pdate

 F

iRmwaRe

It is now possible to remotely update the 3411’s firmware via the web interface. Just select the update 
file and click the change firmware button. The “Change Firmware” button will not be enabled until 
a valid update file has been selected. Once the update process has completed the 3411 will reboot 
with the new version of the firmware installed.

Figure 5–4  Update Firmware

5.4 

MAG.NET COMMANDS

In order to use the Mag.NET command set, you must first establish a connection with the 3411. There 
are currently three methods to do so, two through USB and one through Ethernet. The commands 
themselves will be described in the next chapter.

5.4.1 

UsB C

ommUniCation

 d

eviCe

 C

lass

 C

onneCtion

You may connect to the 3411 using Hyper-terminal, Tera-Term, Putty or any custom program which 
can open a Virtual COM Port.  The following are the valid communication parameters for the RS-
232 connection:

•  No parity 
•  8 Data Bits
•  1 Stop bit
•  No protocol
•  921600 Baud rate

Summary of Contents for 3411




























































Reviews:

No comments