Magrini MC75, Instructions For Use

Page: 1 / 2

Magrini Limited
Unit 5, Maybrook Industrial Estate, Brownhills, Walsall WS8 7DG
Tel: 01543 375311 Fax: 01543 361172 Email: sales@magrini.co.uk Web: www.magrini.co.uk Magrini Limited
Unit 5, Maybrook Industrial Estate, Brownhills, Walsall WS8 7DG
Tel: 01543 375311 Fax: 01543 361172 Email: sales@magrini.co.uk Web: www.magrini.co.uk
INSTRUCTIONS FOR USE
Magrini Baby Changing Unit - Model MC75
Doc: MC7503 Date: February 2014
INSTRUCTIONS FOR USE
Magrini Baby Changing Unit - Model MC75
IMPORTANT: RETAIN FOR FUTURE REFERENCE. READ CAREFULLY.
This changing unit must be fixed to the wall for safe use of the product and the fastenings used
should be appropriate to the wall.
To assure proper installation, we suggest that a qualified person install this unit.
Magrini Ltd., will not be responsible if the changing station is not installed correctly.
All recommended fixings are supplied. Replacements are available free of charge from Magrini -
do not use less substantial fittings.
We DO NOT recommend fixing onto toilet or changing room cavity walls, unless specific
studwork is in place. If in doubt contact the Magrini sales office.
PLEASE NOTE: this unit does not require a changing pad and therefore, no pad is supplied with
this unit.
Tools required:
•
Drill
•
10mm Masonry Drill Bit
For fixing into blockwork or brickwork:
1) Using the template supplied, mark the position of the holes to be drilled ensuring that the correct height of
79cm from the floor to the bottom of the template is correct. Check for correct level. Drill the 2 top holes and
2 middle holes, fit the plastic block fixings (supplied). Use four M8x70 turbo coach screws into the top four
block fixings.
2) Screw into block fixings and allow 10mm protruding. Test fit unit for level and verify correct position of mark
for bottom two holes. Remove unit and drill bottom two holes and fit the plastic block fittings. Tighten top
four screws until approximately 4mm protruding. Fit unit over screws and push down to lock into slots.
3) Use the remaining two M8x70 turbo coach screws. Screw into the bottom two holes of the unit and into the
block fixings and tighten.
4) Pull unit open and close several times to check for correct movement.
Note: All assembly fittings shall always be correctly tightened and checked regularly. Screws shall not be
loose because a child can squeeze parts of the body, or clothing (e.g. strings, necklaces, ribbons for
babies, dummies, etc.) could get caught. There would be danger of strangulation.
Units should be fitted no less than 100mm from the corner of the room to enable access for cleaning.
Be aware of the risk of open fire and other sources of strong heat, such as electric bar fires, gas fires etc.
in the near vicinity of the unit.
6 No. Fixing Plugs
10mm x 60mm
Cleaning Instructions
The nappy changing unit may be washed and wiped with a damp soft cloth or sponge. Use of mild
detergent and warm water will remove the majority of dust and stains. For more obstinate stains a
domestic cream cleaner can be used. Do not use any
abrasive cloths, caustic or solvent cleaners as these may
damage the unit.
Maintenance Instructions
Check that the unit is securely fixed to the wall.
Check that the changing bed does not
rest below the horizontal position.
Ensure warning label is in place on the
inside of the unit and general
cleanliness is within given guidelines.
Ensure closing mechanism returns the
tray to the upright position. Any
replacement parts must be obtained
from Magrini only.
WARNING: DO NOT LEAVE THE CHILD UNATTENDED.
Intended for use for children up to a maximum weight of 15kg.
Do not use the changing unit when any part is broken, torn or missing.
Changing Unit Fixing Parts (supplied):
6 No. Turbo Coach Screws M8 x 70
Hexagon Head, C-1022 Steel/Zinc Plated
Yellow Passivated
•
10mm Hex Socket or Spanner
•
Spirit Level
TEMPLATE
SUPPLIED
Drill
(10mm Masonry Bit)
Drill
(10mm Masonry Bit)
79cm (31”) 79cm (31”)
Floor Level
Magrini Limited
Unit 5, Maybrook Industrial Estate, Brownhills, Walsall WS8 7DG
Tel: 01543 375311 Fax: 01543 361172 Email: sales@magrini.co.uk Web: www.magrini.co.uk Magrini Limited
Unit 5, Maybrook Industrial Estate, Brownhills, Walsall WS8 7DG
Tel: 01543 375311 Fax: 01543 361172 Email: sales@magrini.co.uk Web: www.magrini.co.uk
INSTRUCTIONS FOR USE
Magrini Baby Changing Unit - Model MC75
Doc: MC7503 Date: February 2014
INSTRUCTIONS FOR USE
Magrini Baby Changing Unit - Model MC75
IMPORTANT: RETAIN FOR FUTURE REFERENCE. READ CAREFULLY.
This changing unit must be fixed to the wall for safe use of the product and the fastenings used
should be appropriate to the wall.
To assure proper installation, we suggest that a qualified person install this unit.
Magrini Ltd., will not be responsible if the changing station is not installed correctly.
All recommended fixings are supplied. Replacements are available free of charge from Magrini -
do not use less substantial fittings.
We DO NOT recommend fixing onto toilet or changing room cavity walls, unless specific
studwork is in place. If in doubt contact the Magrini sales office.
PLEASE NOTE: this unit does not require a changing pad and therefore, no pad is supplied with
this unit.
Tools required:
•
Drill
•
10mm Masonry Drill Bit
For fixing into blockwork or brickwork:
1) Using the template supplied, mark the position of the holes to be drilled ensuring that the correct height of
79cm from the floor to the bottom of the template is correct. Check for correct level. Drill the 2 top holes and
2 middle holes, fit the plastic block fixings (supplied). Use four M8x70 turbo coach screws into the top four
block fixings.
2) Screw into block fixings and allow 10mm protruding. Test fit unit for level and verify correct position of mark
for bottom two holes. Remove unit and drill bottom two holes and fit the plastic block fittings. Tighten top
four screws until approximately 4mm protruding. Fit unit over screws and push down to lock into slots.
3) Use the remaining two M8x70 turbo coach screws. Screw into the bottom two holes of the unit and into the
block fixings and tighten.
4) Pull unit open and close several times to check for correct movement.
Note: All assembly fittings shall always be correctly tightened and checked regularly. Screws shall not be
loose because a child can squeeze parts of the body, or clothing (e.g. strings, necklaces, ribbons for
babies, dummies, etc.) could get caught. There would be danger of strangulation.
Units should be fitted no less than 100mm from the corner of the room to enable access for cleaning.
Be aware of the risk of open fire and other sources of strong heat, such as electric bar fires, gas fires etc.
in the near vicinity of the unit.
6 No. Fixing Plugs
10mm x 60mm
Cleaning Instructions
The nappy changing unit may be washed and wiped with a damp soft cloth or sponge. Use of mild
detergent and warm water will remove the majority of dust and stains. For more obstinate stains a
domestic cream cleaner can be used. Do not use any
abrasive cloths, caustic or solvent cleaners as these may
damage the unit.
Maintenance Instructions
Check that the unit is securely fixed to the wall.
Check that the changing bed does not
rest below the horizontal position.
Ensure warning label is in place on the
inside of the unit and general
cleanliness is within given guidelines.
Ensure closing mechanism returns the
tray to the upright position. Any
replacement parts must be obtained
from Magrini only.
WARNING: DO NOT LEAVE THE CHILD UNATTENDED.
Intended for use for children up to a maximum weight of 15kg.
Do not use the changing unit when any part is broken, torn or missing.
Changing Unit Fixing Parts (supplied):
6 No. Turbo Coach Screws M8 x 70
Hexagon Head, C-1022 Steel/Zinc Plated
Yellow Passivated
•
10mm Hex Socket or Spanner
•
Spirit Level
TEMPLATE
SUPPLIED
Drill
(10mm Masonry Bit)
Drill
(10mm Masonry Bit)
79cm (31”) 79cm (31”)
Floor Level
INSTRUCTIONS FOR USE
Magrini Baby Change Unit - Model MC75
INSTRUCTIONS FOR USE
Magrini Baby Change Unit - Model MC75
Magrini Limited, Unit 5 Maybrook Industrial Estate, Brownhills, Walsall WS8 7DG
t : 01543 375311 • e : sales@magrini.co.uk
•
w : www.magrini.co.uk
Doc: MC7504 Date: August 2017
Magrini Limited, Unit 5 Maybrook Industrial Estate, Brownhills, Walsall WS8 7DG
t : 01543 375311 • e : sales@magrini.co.uk
•
w : www.magrini.co.uk
For fixing into blockwork or brickwork:
1) Using the template supplied, mark the position of the holes to be drilled ensuring that the correct height of
79cm from the floor to the bottom of the template is correct. Check for correct level. Drill the 2 top holes
and 2 middle holes, fit the plastic block fixings (supplied). Use four M8x70 turbo coach screws into the top
four block fixings.
2) Screw into block fixings and allow 10mm protruding. Test fit unit for level and verify correct position of
mark for bottom two holes. Remove unit and drill bottom two holes and fit the plastic block fittings. Tighten
top four screws until approximately 4mm protruding. Fit unit over screws and push down to lock into slots.
3) Use the remaining two M8x70 turbo coach screws. Screw into the bottom two holes of the unit and into the
block fixings and tighten.
4) Pull unit open and close several times to check for correct movement.
Note: All assembly fittings shall always be correctly tightened and checked regularly. Screws shall not
be loose because a child can squeeze parts of the body, or clothing (e.g. strings, necklaces,
ribbons for babies, dummies, etc.) could get caught. There would be danger of strangulation.
Units should be fitted no less than 100mm from the corner of the room to enable access for
cleaning. Be aware of the risk of open fire and other sources of strong heat, such as electric bar
fires, gas fires etc. in the near vicinity of the unit.
Cleaning Instructions
The nappy changing unit may be washed and wiped with a damp soft cloth or sponge. Use of mild
detergent and warm water will remove the majority of dust and stains. For more obstinate stains adomestic
cream cleaner can be used. Do not use anyabrasive cloths,
caustic or solvent cleaners as these maydamage the unit.
Maintenance Instructions
Check that the unit is securely fixed to the wall.
Check that the changing bed does not rest
below the horizontal position. Ensure
warning label is in place on the inside
of the unit and general cleanliness is
within given guidelines. Ensure closing
mechanism returns the tray to the
upright position. Any replacement parts
must be obtained from Magrini only.
IMPORTANT: RETAIN FOR FUTURE REFERENCE. READ CAREFULLY.
This changing unit must be fixed to the wall for safe use of the product and the fastenings used
should be appropriate to the wall.
To assure proper installation, we suggest that a qualified person install this unit. Magrini Ltd., will
not be responsible if the changing station is not installed correctly.
All recommended fixings are supplied. Replacements are available free of charge from Magrini -
do not use less substantial fittings.
We DO NOT recommend fixing onto toilet or changing room cavity walls, unless specific studwork
is in place. If in doubt contact the Magrini sales office.
PLEASE NOTE: this unit does not require a changing pad and therefore, no pad is supplied with
this unit.
6 No. Turbo Coach Screws M8 x 70 Hexagon Head,
C-1022 Steel/Zinc Plated Yellow Passivated 6 No. Fixing Plugs
10mm x 60mm
Changing Unit Fixing Parts (supplied):
WARNING: DO NOT LEAVE THE CHILD UNATTENDED.
Intended for use for children up to a maximum weight of 15kg.
Do not use the changing unit when any part is broken, torn or missing.
Tools required:
• Drill • 10mm Hex Socket or Spanner
•10mm Masonry Drill Bit • Spirit Level